Setting The Start Address; Cleaning The Spotlight; Dmx Channels And Functions - Leuchtkraft ODC-100/CTW Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
The easiest way to terminate the DMX out-
put of the ODC-100/CTW is to separate an
extension cable ODP-34DMX and to connect
the resistor to the pins 2 and 3 of the plug .
Connect the plug with the resistor to the inline
jack of the cable DMX OUT . If no terminating
resistor is required, screw the protective cover
provided onto the inline jack of the cable .

4.3.2 Setting the start address

For separate control of all DMX units connected
to the light controller, each unit must have its own
start address . Example: If the first DMX channel of
the spotlight is to be controlled by the light con-
troller via DMX address 17, set the start address
on the spotlight to 17 . All other DMX channels
of the spotlight will be automatically assigned to
the following addresses (i . e . the addresses 18 – 20
for the start address 17) .
1) Press the button MENU repeatedly until the
display shows
2) Press the button ENTER . The display will show
the start address adjusted (
3) To set the desired address, press the buttons
UP and DOWN . Now the spotlight can be
operated via the light controller .
Notes:
1 . If the DMX control does not work, call up the menu
item
and press the button ENTER .
appear on the display . If
play, use the button UP or DOWN to switch to
2 . When the menu item
on the display and DMX signals are available at the
DMX input, the dot at the right end of the display
will flash .

4.3.3 DMX channels and functions

DMX
DMX
channel
value
1
000 – 255
2
000 – 255 basic brightness cool white
000 – 255 basic brightness warm white
3
000 – 010
4
011 – 255
Fig. 6 DMX overview
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
.
...
appears on the dis-
,
or
appears
Function
brightness 0 %  100 %
stroboscope off
stroboscope slow  fast
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®

5 Cleaning the Spotlight

Clean the pane in front of the LED at regular inter-
vals depending on impurities . This is the only way
to ensure that light will be emitted at maximum
brightness . Before cleaning, disconnect the
mains plug from the socket. Only use a soft
clean cloth and a glass cleaner .
For cleaning the other parts of the housing of
the PARC-100 / CTW, only use a soft clean cloth .
Never use any fluid; it may leak into the spotlight
and damage it . The weatherproof housing of the
ODC-100 / CTW may also be cleaned with a damp
cloth and a mild detergent .
6 Specifications
Data protocol: . . . . . . . . . . . DMX 512
Number of DMX channels: . 4
Light source: . . . . . . . . . . . . COB LED
Power consumption: . . . . . 100 W
Beam angle: . . . . . . . . . . . 60°
Colour temperature: . . . . . adjustable
) .
DMX connections: . . . . . . . XLR, 3 poles
Pin assignment: . . . . . . . . Pin 1 = ground
Power supply: . . . . . . . . . . . 230 V/ 50 Hz
must
Power consumption: . . . . . . 120 VA max .
.
Protection of housing: . . . . . IP 66 (ODC- only)
Dimensions w/o
mounting bracket: . . . . . . . ⌀ 185 × 250 mm
Weight: . . . . . . . . . . . . . . . 6 .5 kg
Subject to technical modification .
2700 K – 5600 K
Pin 2 = DMX−
Pin 3 = DMX+
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Parc-100/ctw38.708038.7110

Tabla de contenido