Velleman WS610PF Manual Del Usuario página 4

Photo frame
•
Insert a suitable SD/MMC card, contact pins facing the front of weather station. Make sure the
images are in JPEG format and smaller than 4000x4000 pixels.
Note: When the SD card is not recognized, the message 'No SD card' is displayed. Make sure
to use the proper SD/MMC card (32MB~2GB).
When picture pixel size is more than 4000x4000, the message 'Too Large Size' is
displayed.
•
Press and hold the On/Off button [C] for ±5s to switch off the photo display [A]. Press again to
switch it on.
•
Set the time interval of the slideshow by pressing the mode button [D]. Available modes: 5s,
10s, 30s or infinite (manual mode). The selected mode is displayed for a few seconds in the
upper right corner.
•
When in manual mode, press the
the button to see the next image.
•
At any time during image display, press and hold the
contrast settings (darker, min. value 1) or press and hold the
image contrast settings (lighter, max. value 28).
•
Press the rotate button [E] to rotate the image over 90°, 180°, 270° or back to original
position (0°)
Weather forecast
•
A weather forecast is given by displaying icons [B1] on the data display [B].
o a 'sun' when humidity is between 19% and 40% RH
o a 'sun + cloud' when humidity is between 41% and 65% RH
o a 'cloud' when humidity is between 66% and 75% RH
o a 'cloud + rain' when humidity is between 76% and 91% RH
Setting date and time
•
To set the date and time press and hold the Date/Time button [F] until the hour-mode (12/24)
starts flashing. Press the Set/Day button [J] to switch between 12h and 24h display and press
the Date/Time button [F] again to confirm. The seconds-indication starts flashing.
•
Press the Set/Day button [J] to reset the seconds to '00' and press the Date/Time button [F]
to confirm. The hour-indication starts flashing.
•
Press the Set/Day button [J] until the correct hour is shown; press and hold to advance faster.
Press the Date/Time button [F] to confirm. The minutes-indication starts flashing
•
Press the Set/Day button [J] until the correct minutes are shown; press and hold to advance
faster. Press the Date/Time button [F] to confirm. The year-indication starts flashing.
•
Press the Set/Day button [J] until the correct year is shown; press and hold to advance faster.
Press the Date/Time button [F] to confirm. The month-indication starts flashing.
•
Press the Set/Day button [J] until the correct day is shown; press and hold to advance faster.
Press the Date/Time button [F] to confirm. The clock has been set and returns to normal
display.
•
to switch between displaying seconds or day of the week press the Set/Day button [J] during
normal time display.
Note: after ±30s of inactivity, the clock returns to normal operation mode.
Setting an alarm
•
During normal time display, press the alarm button [I]. The alarm time is shown.
•
To set the alarm time, press and hold the alarm button [I] until the hour-indication flashes.
•
Press the Set/Day button [J] until the desired hour is shown; press and hold to advance faster.
Press the alarm button [I] to confirm. The minutes-indication starts flashing.
•
Press the Set/Day button [J] until the desired minutes are shown; press and hold to advance
faster. Press the alarm button [I] to confirm.
•
To enable or disable the alarm, press the Set/Day button [J] when in alarm time display. A
small icon is shown next to the time when the alarm is enabled.
•
When the set alarm time is reached, the alarm will sound for ±30s. To stop the alarm, press the
alarm button [I]; to put the alarm on hold for ±8 minutes press the snooze button [L]. When
snooze mode is activated, a small Z
snooze mode press the alarm button [I].
24/04/2009
WS610PF
button shortly to see the previous image or press
z
-symbol is flashing next to the time indication. To end
4
button to decrease image
button to increase
©2009 Velleman ® Components nv