Troubleshooting; Fault Table; Maintenance And Cleaning; Maintenance Plan - Starmix haaga 355 Manual De Instrucciones

Troubleshooting

8. Troubleshooting
WARNING
Risk of cutting due to broken glass, metal
or other sharp edged materials!
EN
When emptying the sweeping container,
cutting injuries may occur due to broken glass,
metal or other sharp edged materials.
• Wear the prescribed personal protective
equipment!
CAUTION
Health impairments caused by dust
resulting from sweeping!
The inhalation of dusts can endanger the
health.
• Wear the prescribed personal protective
equipment!
CAUTION
Risk of injury through tipping over of the
telescopic bracket!
Tipping over of the telescopic bracket may
lead to slight injuries, such as jamming of
the finger or haematomas in users or other
persons.
• When carrying the device, hold it so that the
telescopic bracket cannot tip over.
Even if the prescribed maintenance work and
checks of the device before use are complied
with, faults may occur. Possible faults are listed
in the table below, with specification of the cause
and remedy.
26
haaga 355

8.1 Fault table

Fault Cause Remedy
Device is Clean device, see
contaminated Section
Broom blocked Remove blockage see
Section "Remove
blockage"
Contaminated Clean broom drives, see
Device is broom drives Section "Clean device"
running with
Height Set height adjustment,
difficulty or
adjustment see Section in the
roughly
is set too section "Adjust height
low, contact setting"
pressure of the
plate brooms
too high
Plate brooms do Contact Service
not rotate
Bristles are Improper Align the bristles, see
bent storage Section in the section
"Align bristles"
Sweeping Sweeping lip is Replace sweeping lip
result is missing, loose
insufficient or worn
haaga 355
9.

Maintenance and cleaning

WARNING
Risk of cutting due to broken glass, metal
or other sharp edged materials!
When emptying the sweeping container,
cutting injuries may occur due to broken glass,
metal or other sharp edged materials.
• Wear the prescribed personal protective
equipment!
CAUTION
Health impairments caused by dust
resulting from sweeping!
The inhalation of dusts can endanger the
health.
• Wear the prescribed personal protective
equipment!
CAUTION
Risk of injury through tipping over of the
telescopic bracket!
Tipping over of the telescopic bracket may
lead to slight injuries, such as jamming of
the finger or haematomas in users or other
persons.
• When carrying the device, hold it so that the
telescopic bracket cannot tip over.
CAUTION
Hazard due to cleaning materials!
The agents can contain harmful ingredients
and can thereby cause irritation of the
respiratory tract and the skin.
• Observe the manufacturer's safety data
sheet.
• Avoid spillage and the formation of fog.
• Do not eat, drink or smoke while working.
• Avoid contact with skin and eyes.
Maintenance and cleaning
In the following sections the maintenance and
cleaning work required for optimal and fault-free
operation is described.
The conduct of the specified work depends
in some cases on time and/or load. For the
maintenance interval information shown both in
deadlines and service hours, the one that occurs
first applies.
In case of questions on the maintenance work
and intervals contact the manufacturer.

9.1 Maintenance plan

Maintenance Maintenance work
interval
Before Check the device to make sure that it
starting is functioning before starting work. If
work necessary, contact the Service.
Check the telescopic sliding bracket to make
sure that it is firmly fixed in the handles.
Check the sweeping container to make sure
it is firmly fixed and in good condition.
Check the plate brooms and the fine dust
sweeping roller for rolled up threads and
cords. Remove these if necessary.
Check the plate brooms and the fine dust
sweeping roller for jammed items or contami-
nation.
Check the handle for contamination and
clean its if necessary.
Check that the height adjustment is at the
correct height.
Check the sweeping pressure setting. Adapt
this to the surface to be swept, if necessary.
After finishing Empty the sweeping container.
work
Clean the device.
8 Bh Clean broom drives.
9.2 Remove blockage
• Remove wound-up material (e.g. cords,
threads, etc.) from the brooms and axes.
• Remove jammed material (e.g. stones, twigs,
leaves etc.).
EN
27