Prior To Operation; Using The Controls; Maintenance And Inspection - Hitachi Koki RB 36DL Instrucciones De Manejo

4. Disconnect the charger's power cord from the
receptacle
5. Hold the charger fi rmly and pull out the battery
NOTE
After charging, pull out batteries from the charger fi rst,
and then keep the batteries properly.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes weaker,
stop using the tool and recharge its battery. If you continue
to use the tool and exhaust the electric current, the battery
may be damaged and its life will become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights up green. In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged
with UC36YRSL is taken out, wait for a minimum of 3
seconds before reinserting it to continue charging. If the
battery is reinserted within 3 seconds, the battery may
not be properly charged.

PRIOR TO OPERATION

○ Setting up and checking the work environment
Check if the work environment is suitable by following
the precautions.

USING THE CONTROLS

(FUNCTIONS)
● The mode switch and remaining battery display
functions (Fig. 3)
NOTE
The turbo mode turns off automatically and
returns to the previous mode after 10 seconds
in order to protect the electronic circuitry. Press
the turbo mode switch again to switch back to
the turbo mode.
● About Remaining Battery Indicator (Fig. 4)
CAUTION
Never hit or subject the switch panel to strong shocks.
Doing so will damage it.
NOTE
○ To conserve the battery, the lamps only light when the
battery remaining switch is pressed.
○ Unless a battery is mounted to the blower and the switch
is pressed once, the lamps will not light even if the
battery remaining switch is pressed.
● Work Capacity on a Full Charge
The following is a rough estimate of the amount of
work provided by the blower when on a full charge.
(The amount of work varies somewhat due to ambient
temperature and characteristics of the battery)
Time in continuous operation when switch fully depressed
in each mode
Battery
BSL3620
Mode
Mode 1 23 min.
Mode 2 15 min.
Mode 3 11 min.
Mode 4 8 min.
MOUNTING AND OPERATION
Action
Inserting the battery cover
Charging
The mode switch and remaining
battery display functions
About remaining battery indicator
Mounting the extension nozzle
Removing and inserting the
battery
Turning the blower on
Selecting accessories
NOTE
BL36200...For details of the
operations, please see the
BL36200 instruction manual.

MAINTENANCE AND INSPECTION

1. Inspecting the nose grill
Before and after use, check and make sure the nose
grill, which covers the air intake, is not damaged. If it
is damaged, contact your sales outlet or the Hitachi
Authorized Service Center to have it repaired.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the coldless blower is stained, wipe with a
soft dry cloth or a cloth moistened with soapy water.
Do not use chloric solvents, gasoline or paint thinner, for
they melt plastics.
If the nose grill is blocked with debris, the blower will
work less effi ciently.
Clean it gently when necessary with a soft brush.
5. Storage
Store the coldless blower in a place in which the
temperature is less than 40°C and out of reach of
children.
7
English
BSL3626 BL36200
(sold separately) (sold separately)
29 min. 231 min.
19 min. 149 min.
14 min. 109 min.
10 min. 80 min.
Figure Page
1 184
2 184
3 184
4 184
5 185
6 185
7 185
― 186