Prior To Operation; Using The Blower - Hitachi Koki RB 36DL Instrucciones De Manejo

English
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are as
shown in Table 2, and batteries that have become hot
should be cooled for a while before being recharged.
Table 2 Recharging ranges of batteries
Rechargeable
batteries
BSL3620
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BSL3620
NOTE
The charging time may vary according to temperature
and power source voltage.
4. Disconnect the charger's power cord from the
receptacle
5. Hold the charger firmly and pull out the battery
NOTE
After charging, pull out batteries from the charger
first, and then keep the batteries properly.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION
If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the pilot lamp of the charger lights up green. In
such a case, first let the battery cool, then start
charging.
When the pilot lamp flickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects
in the charger's battery connector. If there are no
foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
Since the built-in micro computer takes about 3
seconds to confirm that the battery being charged
with UC36YRSL is taken out, wait for a minimum of 3
seconds before reinserting it to continue charging. If
the battery is reinserted within 3 seconds, the battery
may not be properly charged.
12
Temperatures at which the
battery can be recharged
0°C – 50°C
UC36YRSL
Approx. 60 min.

PRIOR TO OPERATION

Setting up and checking the work environment
Check if the work environment is suitable by following
the precautions.

USING THE BLOWER

WARNING
Do not use when your field of vision is poor, such as
at night or in inclement weather.
Do not use in the rain or on wet ground after it has
rained.
Always be careful of your footing when using the
blower so you don't slip and lose your balance.
Do not use on steep slopes.
Pay attention to which way the blower is pointed to
avoid people and things that may be broken easily,
such as windows.
Be careful about working in confined spaces or
blowing into the wind to avoid flying objects coming
back and hitting you.
Do not get closer than 5 meters from others. And
when 2 or more people are working, keep a distance
of at least 5 meters from each other.
When attaching or removing the extension nozzle
always release the switch and remove the battery
from the blower to prevent an accident.
Keep the air intake away from your body as it may
suck your work clothes against the air intake.
CAUTION
Mount the battery securely to the blower.
If it is not mounted securely, it may fall off and cause
an injury.
If something gets in the air intake, causing the blower
to stop, release the switch immediately, then remove
the battery before trying to dislodge the foreign object.
Working with the blower
1. Mounting the extension nozzle (Fig. 6)
Align the Protrusion on the extension nozzle with the
groove in the body and press it in
until it stops to secure it.
B
2. Mounting the battery (Fig. 2)
Press the battery in as shown at right until it makes a
clicking sound as it catches.
3. Turning the blower on (Fig. 5)
• Make sure there is nothing in the area that might go
flying and cause an accident.
• Point the extension nozzle at whatever you wish to
clean and depress the switch.
• Operate with one hand during use. Grasp the handle
with either your left or your right hand, select the
operating mode with the mode switch and adjust
how far in you depress the switch as you are working.
; then twist it
A