Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: In case of the first pairing process, a PIN Code request
will be displayed. Type in „000000" as PIN Code.
NOTE: The app is set to remember and search the device
which has paired last time for 30 seconds. If the app is not
able to find the previously paired ACE AFM-5 for 30 seconds,
the app will show a request message. If you want the app to
find another ACE AFM-5, press „OK", and if you want the app to
keep finding the previously paired ACE AFM-5, press „Cancel".
Step 4. Choose a user. Each test result will be saved separately
according to the selection of the user. All history of saved test
results are viewable from the Graphic Icon at the bottom of
the menu.
Step 5. The circular bar on the app indicates the progress of
warm-up. When warming up gage reaches 95, take a deep
breath and get ready for blowing.
Step 6. When „Start blowing" is displayed, blow for 5 seconds
into the mouthpiece until the gage reaches 100 or you feel the
air has been pulled through the air pump in the ACE AFM-5
with a click.
NOTE: If the camera feature is enabled, the camera will
automatically capture the image of a user once the blowing
has been completed.
Step 7. If a sufficient breath sample is taken correctly, the
„Analyzing data" will be shown on the app. NOTE: If insufficient
sample is taken, an error message will displayed. To test again,
press „OK" on the app. NOTE: In the graph, the test results
performed without app will be shown as „D".
Step 8. After a few seconds the estimated blood alcohol
concentration will be displayed on the app in per mill (3 digits,
2 decimals/per mill = default setting). The result may vary
depending on the concentration which has been measured
during the last test. In this page, the app enables you to make
a memo which is viewable with test results from the Graph icon
and the test results can be also shareable via Text message,
Facebook, or Twitter.
Step 9. Tap either „Retest" or „BAC level" on the app (or press
Power button on the ACE AFM-5) to test again without selecting
a user. If you want to start test again from the beginning, tap
the Home Icon at the bottom menu.
Step 10. Press and hold Power button on the ACE AFM-5 for
2 seconds to turn it off when you have finished testing.
NOTE: The device will turn off automatically if the device is
not in use for 2 minutes. If you exit the app while the device
is working with the app, all Blue, Red and Green LEDs on the
device will flicker together. Press Power Button on the device
to restart.
19
Operation without App (Standalone mode)
NOTE: To activate Standalone mode, you have to pair the ACE
AFM-5 with the app and set „Limit Line" first. (Pair with the app
and go to the setting on the app to set „Limit Line".) Once
„Limit Line" is set, the set value will be sent to the ACE AFM-5,
and the test result on Standalone mode will be displayed with
indications of Red or Green LEDs according to the set value of
„Limit Line". (After setting the value of „Limit Line", you should
move into Home by tapping the Home Icon at the bottom
menu on the app in order to save and transfer the set value to
the ACE AFM-5.)
NOTE: If the battery is low or the device is in unacceptable
temperature range, all Blue, Red and Green LEDs will flicker
together. Replace a new battery or try again after the device
has reached a temperature within the operating range (5-40°C).
Step 1. To turn on the ACE AFM-5, press and hold Power button
for a second until the Blue, Green and Red LEDS appear on
the device.
Step 2. If the app on your smartphone is off and there is no
pairing signal from the app, the device will move into the
Standalone Mode and starts the warm-up automatically. A Blue
LED keeps blinking until the warm-up process is completed.
NOTE: If the device doesn't have the set value of „Limit line",
all Blue, Red and Green LEDs will flicker together after the
warm-up process. Pair the device with the app and set „Limit
Line" on the setting menu of the app. If you turn on the app
on you smartphone while using the device in the Standalone
Mode, the device will move into the App Mode and start pairing
automatically. (If you turn on the app while the device is under
the blowing or analyzing process in the Standalone Mode, the
device will move into the App Mode after completing these
processes.)
Step 3. When the Blue LED stops blinking and remains on,
it means the device is ready for blowing. Take a deep breath
and blow for 5 seconds into the mouthpiece until the Blue
LED disappears.
Step 4. If a sufficient breath sample is taken correctly, Green
and Red LEDs will blink in turns and the test result will be
displayed in a few seconds. NOTE: If an insufficient breath
sample is taken, blue, red and green LEDs will flicker together.
Press Power button to retest.
Step 5. Test results will be displayed with indications of Red
or Green LEDs according to the set value of „Limit Line" as
follows. Press Power Button to retest.
Step 6. Press and hold Power button for 2 seconds to turn it off
when you have finished testing
NOTE: The device will turn off automatically if the device is not
in use for 2 minutes.
20
Publicidad
