Parámetros Del Grupo De Programación Avanzada - AB Quality Allen-Bradley PowerFlex 400 Manual Del Usuario

Español-22
Parámetros del grupo de programación avanzada:
No. Parámetro
A141 [Purge Frequency]
A142 [Internal Freq]
A143 [Preset Freq 0]
A144 [Preset Freq 1]
A145 [Preset Freq 2]
A146 [Preset Freq 3]
A147 [Accel Time 2]
A148 [Decel Time 2]
A149 [S Curve %]
A150 [PID Trim Hi]
A151 [PID Trim Lo]
A152 [PID Ref Sel]
A153 [PID Feedback Sel]
A154 [PID Prop Gain]
A155 [PID Integ Time]
A156 [PID Diff Rate]
A157 [PID Setpoint]
A158 [PID Deadband]
A159 [PID Preload]
A160 [Process Factor]
A163 [Auto Rstrt Tries]
A164 [Auto Rstrt Delay]
A165 [Start At PowerUp]
A166 [Reverse Disable]
A167 [Flying Start En]
A168 [PWM Frequency]
A169 [PWM Mode]
A170 [Boost Select]
Sólo está activo cuando A125 [Torque Perf
Mode] se establece en 0 "V/Hz".
A171 [Start Boost]
Sólo está activo cuando A084 [Boost Select] y A125 [Torque Perf Mode] se establecen en "0".
A172 [Break Voltage]
Sólo está activo cuando A084 [Boost Select] y A125 [Torque Perf Mode] se establecen en "0".
A173 [Break Frequency]
Sólo está activo cuando A084 [Boost Select] y A125 [Torque Perf Mode] están establecidos en "0".
A174 [Maximum Voltage]
A175 [Slip Hertz @ FLA]
A176 [DC Brake Time]
A177 [DC Brake Level]
A178 [DC Brk Time@Strt] 0.0/99.9 Seg
A179 [Current Limit 1]
A180 [Current Limit 2]
A181 [Motor OL Select]
A182 [Drive OL Mode]
A183 [SW Current Trip]
Variador de CA de frecuencia ajustable PowerFlex 400 Inicio rápido
Mín./ Máx. Visualización/opciones
0.0/320.0 Hz 0.1 Hz
0.00/320.00 Hz 0.01 Hz
0.0/320.0 Hz 0.1 Hz
0.00/600.00 Seg 0.01 Seg
0.00/600.00 Seg 0.01 Seg
0/100% 1%
0.0/320.0 Hz 0.1 Hz
0.0/320.0 Hz 0.1 Hz
0/8 0 = "PID Disabled"
1 = "PID Setpoint"
2 = "Analog In 1"
3 = "Analog In 2"
0/2 0 = "Analog In 1"
1 = "Analog In 2"
0.00/99.99 0.01
0.0/999.9 Seg 0.1 Seg
0.00/99.99 (1/Seg) 0.01 (1/Seg)
0.0/100.0% 0.1%
0.0/10.0% 0.1%
0.0/320.0 Hz 0.1 Hz
0.1/999.9 0.1
0/9 1
0.0/160.0 Seg 0.1 Seg
0/1 0 = "Disabled"
0/1 0 = "Rev Enabled"
0/1 0 = "Disabled"
2.0/8.0, 10.0 kHz 0.1 kHz
0/1 0 = "Space Vector"
0/15 Selecciones en % del voltaje base.
0 = "Custom V/Hz"
Par variable
1 = "30.0, VT"
2 = "35.0, VT"
3 = "40.0, VT"
4 = "45.0, VT"
1.1%
0.0/25.0%
0.0/100.0% 0.1%
0.1 Hz
0.0/320.0 Hz
20/Rated Volts 1 VAC
0.0/10.0 Hz 0.1 Hz
0.0/99.9 Seg 0.1 Seg
0.0/(Drive Amps × 1.5) 0.1 Amps
0.1 Seg
0.0/(Drive Amps × 1.5) 0.1 Amps
0/2 0 = "No Derate"
0/3 0 = "Disabled"
1 = "Reduce CLim"
0.0/(Drive Amps × 1.8) 0.1 Amps
4 = "Comm Port"
5 = "Setpnt, Trim"
6 = "A-In 1, Trim"
7 = "A-In 2, Trim"
8 = "Comm, Trim"
2 = "Comm Port"
1 = "Enabled"
1 = "Rev Disabled"
1 = "Enabled"
1 = "2-Phase"
Par constante
5 = "0.0, no IR" 10 = "10.0, CT"
6 = "0.0" 11 = "12.5, CT"
7 = "2.5, CT" 12 = "15.0, CT"
8 = "5.0, CT" 13 = "17.5, CT"
9 = "7.5, CT" 14 = "20.0, CT"
15 = "Kepco"
1 = "Min Derate"
2 = "Max Derate"
2 = "Reduce PWM"
3 = "Both-PWM 1st"
Opción
predeterminada
5.0 Hz
60.00 Hz
0.0 Hz
5.0 Hz
10.0 Hz
20.0 Hz
30.00 Secs
30.00 Secs
20%
60.0 Hz
0.0 Hz
0
0
1.00
2.0 Secs
0.00 (1/Sec)
0.0%
0.0%
0.0%
30.0
0
1.0 Sec
0
1
0
4.0 kHz
1
4
2.5%
25.0%
15.0 Hz
Voltios nom.
2.0 Hz
0.0 Secs
Amps × 0.05
0.0 Secs
Amps × 1.1
0
3
0.0
(inhabilitado)