Technical Data; Before Starting The Equipment - EINHELL GE-CS 18 Li Solo Manual De Instrucciones Original

4. Technical data

Motor power supply: ............................... 18 V DC
Idle speed n : ......................................6500 min
0
Battery charger output voltage: .............. 21 V DC
Battery charger output current: ....................... 3 A
Charging unit
supply voltage: .................... 200-250V~ 50-60Hz
Battery type: ............................................... Li-Ion
Adjustment angle: ............35° to the left and right
Grinding wheel Ø (inside): ........................ 23 mm
Grinding wheel Ø (outside): ........... max. 108 mm
Grinding wheel thickness: ....................... 3.2 mm
Weight: .......................................................1,7 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ..................... 54,1 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 67,1 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Grinding
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_GE_CS_18_Li_SPK7.indb 21 Anl_GE_CS_18_Li_SPK7.indb 21
-1
< 2.5 m/s
2
h
2
- 21 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Assembly (Fig. 3-6)
•
Place the chain clamping mechanism in the
chuck (Fig. 3) and screw from underneath
using the star screw (Fig. 4)
•
Before starting the chain sharpener, fasten
it securely to a suitable surface (e.g. a work-
bench) at a suitable place (protected against
dust, dry, well-lit) using M8 fixing screws and
washers (Fig. 5)
•
Make sure when doing so that the mounting
plate of the chain sharpener is pushed onto
the surface as far as it will go (Fig. 6)
5.2 Charging the Li battery pack (Fig. 17-18)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at.
Warning! Do not actuate the On/Off switch any
more if the protective circuit has tripped. This may
damage the battery.
1. Remove the battery pack from the handle,
pressing the pushlock button (13) downwards
to do so.
14.05.2019 06:48:51 14.05.2019 06:48:51