Sears Craftsman 351.226151 Manual De Uso página 3

RightFax 11/14/2002 9:40 PAGE 4/33 RightF&x
• Use recommended accessories (refer to page 15).
Use of improper accessories may cause risk of
injuryto persons.
• Handle werkpieca correctly. Protect handsfrom pos-
sible injury,
• Turn machine oft if itjams. Blade jams when it digs
too deeply into workplese. (Motor force keeps it
stuckin the work.)
• Always keep drive, cutterhead and blade guards In
place and in proper operating condition.
• Feed work into blade or cutter againstdlrectfonof
rotation.
CAUTION: Think safety! Safety Is a combination of
operatorcommon sense and alertness at all times
when tool is being used,
WARNING: Do not attempt to operate tool untilit is
completely assembled acoordlngto the Instructions.
Check for shippingdamage. If damage has occurred,a
claim must be flied with carrier. Check for complete-
ness. Immediately report missingparts to dealer.
Additionalparts which need to be fastenedto the planer
shouldbe locatedand accountedfor beforeassembling.
Planer is shipped assembled exceptfor the following:
two table extensionswifh rollers, handwhael, handle,
chip chute, knife gauge rod, two knife gauges, hardware
bag, 8/10 mm and 12/16 mm open-endwrenches, and
3, 4, 5 and 6 rnm hex wrenches.
Hardware bag includes:
• 8-1.25 x 20ram Hex Head Bolt (6)
• 6-1.0 x 12mm Socket Head Bolt (3)
• 6-1.0 x 12ram HexWasher Head Bolt (3)
• 6-1.0mm H_ Nut (3)
• 10-1.25mm Hex Nut (1)
• 6turnFlat Washer (6)
• 8mm Flat Washer (6)
• 10mm FlatWasher (1)
• 6rnrnLockWasher (3)
• 8-1.25 x 12mm Set Screw (6)
• 3 CMI-11 E-ring (4)
• 4x 4x 10mm Kay
• Direction Indicator
IMPORTANT: Table is coated wifh a protectant.To
ensure proper fit and operation, remove coating.
Coating Is easily removedwith mild solvents,such as
mineral spirits,and a soft cloth.Avoid getting solution
on paint or any of the rubber or plasticparts.Solvents
may deterioratethese finishes. Use soap and water on
paint, plasticor rubber components, After cleaning,
cover all exposed surfaceswith a light coating of oil
Paste wax Is recommended for table top.
WARNING: Never usa highlyvolatile solvents.Non-
flammable solventsare recommendedto avoidpossible
fire hazard.
WARNING: Do not attempt assembly if parts are
missing. Use this manual to order replacement parts.
PLANER INSTALLATION
Refer to Figure20.
Before planer is assembled, a suitable locationshould
be chosen.The planer weighs approximately550 Ibs
when completely assembled.Planer shouldbe assem-
bled on location.
Planer needs to be set on a flat, level surface.This
improvesstability, accuracy and preventswarpage
and failure of cast components and welds. Adjust
machine levelersor use shimsas required.
Make sure there is arnple room on beth Infeedand
outfeed sidesof planerfor movingthe workplace
through the entire cut,There must be enough room
that neitherthe operatorsnor the bystanderswill
have to stand in linewith the wood while usingthe
tool.
Good lightingand correct power supply (230 volts)
are also requiredfor e properwork area.
Place planer in its designatedspot.Door panel for
access to motor is on back side.The planer is sup-
plied with four moving handles that slide intothe
base on the infeedand outfeed sides.The planer
can be liftedby these handles and movedto the
required location.
MOUNT TABLE EXTENSIONS
Refer to Figure 1, page 4,
• Required hardware:
8-1.25 x 20mm Hex Head Bblt (6)
8rnm Flat Washer (6)
8-1.25 x 12ram Set Screw (6)
• Mount table extensionto planer table on the lnfeed
side usingthree 8-1.25 x 20mrn he_ head boltsand
8mm flat washers, Do not tighten bolts.
• Thread three 8-1.25 x 12mm set screwsinto exten-
sions.
•Placa long straight edge across table and table
extensions.
• Adjust set screws sothat the table extensionis at
the same heightas the table.
• Tighten baits to secure extension.
• Repeat above steps for the outfeed e0(tension.
3