Sears Craftsman 351.226151 Manual De Uso página 5

Righ%F&x 11/14/2002 9:40 PAGE 6/33 RightFax
WARNING: Do not permit fingers to touch the termi-
nals of plug when installing or remevlncfrom outlet.
Grounding Pin
Figure 3 - Grounding Methods
Plugmust be pluggedintoa 230V matchingoutlet(See
Figure3) that is properlyinstaUed and groundedin aocer-
dance with all localcodes and ordinances, D o notmodify
plug provided.If it will notfit in outlet,have properoutlet
Installed_ a qualifiedelectrician.
Inspect tool cords periodically,and if damaged, have
repeited by an authorized servlse facility,
Green (or green and yellow) conductorin cord is the
groundingwire. If repair or replacement of the electric
cord or plug is necessaw, do not connect the green (or
green and yellow) wire to a live terminal.
Where a 2-pmng wall receptacle Is encountered,it
must be replacedwith a properlygrounded3-prong
receptacle installedin accordance with National Electric
Code and local codes and ordinances.
WARNING: This work should be performed by a
qualified electrician.
EXTENSION CORDS
• The use of any extensioncord will cause some drop
Lnvoltage and loss of power.
• Wires of the extension cord must be of sufficientsize
to carry the currentand maintainadequate voltage.
• Use the table to determine the minimumwire size
(A.W.G.) extensioncord.
* Use only 3-wire extension cords having3-prong
groundingtype plugs and 3-pole receptacleswhich
accept the tool plug.
If the extension cord is worn, cut, or damaged in any
way, replace it Immediately.
EXTENSION CORD LENGTH
Wire Size A.W.G.
Upto 50ft ................................ 14
NOTE: Using extension cords ever 50 ft. long Is not
recommended.
ELECTRICAL CONNECTIONS
Refer to Figure 4.
WARNING: All eleotricalconnections mustbe per-
formed by a qcallfled electrician. Make sure unit is off
and disconnectedfrom power sourcewhile motoris
mounted,connected, reconnectedor anytime wiring is
Inspected.
Planer hasan approved 230 volt t hree-conduotor line
curdwitha three-prong grounding t ypeplug, and a 230
volt magnetic contactor that is prewired in the factory
(See Figure 4),
To Motor
Black Red
Ground
Motor ,M
Ground
White t
SetThermal
Ovedoad to
18 AMPS
Rgure 4 - Magnetic Contactor Wiring Schematic
• The tool has a key lock switchto prevent unautho-
rized use. Turn key lock switchto OFF and remove
key when tool is not in use.
NOTE: The motorwellnot start ifthe key is in the OFF
position
• Connect planer to a supplycircuit protectedby a 20
AMP circuitbreaker or time delay fuse.
OVERLOAD PROTECTION
The magneticcentactor has overload protectionthat
helpsto preventdamage to the motor.The overload
protection will automaticallyturn offthe magneticcen-
tactor when an overloadoccurs.Set thermal overloadto
18 Amps. Be sure to disconnectplaner from power
sourcewhen resettingoverload protector. T he protec-
tion is reset by opening the contactor boxand pressing
the reset button.
CHECK CONNECTIONS
• Plug in the line cord to a 230 volt power source.
• Turn the key to ON,
• Turn and release the stop button,
• Depress the start button.The motormust mtate
counterclockwise facing shaft end.
• Depress the stop button.The motor must stop.
• Depressingthe start buttonwith either the stop
buttonpresseddown or the key In OFF position
must not start the motor.
• If any of the above steps do not work properly,dis-
connectplaner from power source and recheckthe
connections.
5