Overhead Rigging - JB Systems Polar Laser Manual De Instrucciones

ENGLISH
cause instant eye injuries, primarily by burning the retina (the light sensitive portion at the back of the eye).
Even if you cannot feel "heat" from a laser beam, it can still potentially injure or blind you or your audience.
 Even very small amounts of laser light are potentially hazardous even at long distances.
 Never look into the laser aperture or laser beams
 Never direct the laser beam to people or animals and
never leave this device running unattended.
 This laser may only be used for shows. The operation
of a class 3B show laser is only allowed if the
operation is controlled by a skilled and well-trained
operator.
 Depending on the classification, operating a laser
product can produce laser radiation that may cause
permanent eye damage and/or skin damage. The
legal instructions for using a laser product vary from country to country. The user must always inform
himself on the legal instructions valid in his country and apply them to his situation.
 The parent document and cornerstone of laser safety standards ANSI Z136.1 (2007) provides guidance for
the safe use of lasers and laser systems by defining control measures for each of the four laser classes.
This valuable document can be obtained from www.laserinstitute.org
Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect installations and
unskilled operation!
DESCRIPTION:
1. MAINS INPUT: with IEC socket and integrated fuse holder and switch, connect the supplied mains
cable here.
2. KEY ACTIVATED SWITCH: used to switch the lasers on/off. Use the keys to make sure only a skilled
operator is able to switch the laser on.
3. ROTATION SPEED KNOB: used to set the rotation speed of the effect
4. RED STROBE: used to adjust the flashing time of the red laser
5. GREEN STROBE: used to adjust the flashing time of the green laser
6. DIMMER: used to adjust the dimming level of the led effect
7. MUSIC INPUT SENSITIVITY: This trimmer is used to adjust the music input sensitivity. Use a
screwdriver to turn the trimmer until the laser works in sync with the music.
8. INTERNAL MICROPHONE: The built-in microphone is used to synchronize the laser show to the beat
of the music.
9. WORKING MODE Selector: used to select the working mode of the unit:
JB SYSTEMS
®
OPERATION MANUAL
3/35 POLAR LASER
ENGLISH
 MANUAL: you can set speed, strobe etc. to your own taste, perfect when the unit is used as
background effect.
 MUSIC: unit works to the rhythm of the music.
 AUTO: unit plays a random program.
10. SAFETY EYE: used to attach a safety cable when the unit is rigged (see paragraph "overhead rigging"
11. HANGING BRACKET: with 2 knobs on the sides to fasten the unit and a mounting hole to fix a
mounting hook.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
OPERATING INSTRUCTIONS
CAUTION EYEDAMAGE: Always position the laser in a way that prevents the
audience from looking directly into the laser beams. The installation should assure that
the beam will not strike the audience.
JB SYSTEMS
®
OPERATION MANUAL
4/35 POLAR LASER