Additional Safety Rules For Tool - Makita 5603R Manual De Instrucciones

Ocultar thumbs Ver también para 5603R:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
ENGLISH
1 Hex wrench
2 Shaft lock
3 Tighten
4 Loosen
5 Saw blade
6 Outer flange
7 Inner flange
8 Outer flange
9 Hex socket head bolt
0 Saw blade
SPECIFICATIONS
Model
Blade diameter ..................................................................... 165 mm
Max. cutting depth
At 90° ................................................................................ 54 mm
At 45° ................................................................................ 38 mm
–1
No load speed (min
) ......................................................... 5,000
Overall length ....................................................................... 330 mm
Net weight ............................................................................ 4.2 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
For model 5705R, public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.36 Ohms it can
be presumed that there will be no negative effects.
The mains socket used for this device must be
protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
ADDITIONAL SAFETY RULES FOR
TOOL
1. Wear hearing protection.
2. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use.
Don't use if lower guard does not close briskly
over saw blade.
CAUTION: If saw is dropped, lower guard may
be bent, restricting full return.
Explanation of general view
q Setting protuberances
w Hex socket head bolt
(For adjusting riving knife)
e Cutting depth
r Loosen
t Lever
y Thumb nut
u For 45° bevel cuts
i For straight cuts
o Base plate
3. Do not use blades which are deformed or
cracked.
4. Do not use blades made of high speed steel.
5. Do not stop the blades by lateral pressure on
the saw blade.
6. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
7. DANGER: Keep Hands Away From Cutting
Area. Keep hands away from blades. Don't
reach underneath work while blade is rotating.
Don't attempt to remove cut material when
blade is moving.
CAUTION: Blades coast after turn off.
8. Support Large Panels. (Fig. A & B)
Large panels must be supported as shown in
Fig. A to minimize the risk of blade pinching
and kickback.
When cutting operation requires the resting of
the saw on the workpiece, the saw shall be
rested on the larger portion and the smaller
piece cut off.
To avoid kickback, do support board or panel
near the cut.
ENB036-2
p 45° angle cuts
a Straight cuts
s Top guide
d Base
f Lock-off button
g Switch trigger
h Vacuum cleaner
j Limit mark
k Brush holder cap
l Screwdriver
5603R
5705R
190 mm
66 mm
46 mm
4,800
356 mm
5.2 kg
5903R
235 mm
85 mm
64 mm
4,500
400 mm
7.6 kg
Fig. A
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

5705r5903r

Tabla de contenido