Bosch GSA 800 PE Professional Manual Original página 17

OBJ_BUCH-647-001.book Page 17 Tuesday, January 29, 2008 3:59 PM
Noise/Vibration Information
Measured values determined according to
EN 60745.
Typically the A-weighted noise levels of the prod-
uct are: Sound pressure level 86 dB(A); Sound
power level 97 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Cutting wood: Vibration emission value
2
a =9.5 m/s , Uncertainty K=2.5 m/s
h
The vibration emission level given in this informa-
tion sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another. It
may be used for a preliminary assessment of ex-
posure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with differ-
ent accessories or poorly maintained, the vibra-
tion emission may differ. This may significantly
increase the exposure level over the total work-
ing period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with the following standards or
standardization documents: EN 60745 according
to the provisions of the directives 2004/108/EC,
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
Dr. Egbert Schneider
Senior Vice President
Engineering
08.01.2008, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
2
.
Replacing/Inserting the Saw Blade
Before any work on the machine itself, pull
the mains plug.
When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching
the saw blade.
When changing the saw blade, take care that
the saw blade holder is free of material resi-
due, e. g. wood or metal shavings.
Selecting a Saw Blade
Use only saw blades suitable for the material be-
ing worked.
An overview of recommended saw blades can be
found at the end of these operating instructions.
The saw blade should not be longer than re-
quired for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
Press the slider for SDS saw blade release 3
downward and insert the saw blade 1 into the
SDS saw blade holder to the stop.
Check the tight seating of the saw blade. A
loose saw blade can fall out and lead to injuries.
Removing the Saw Blade
Press the slider for SDS saw blade release 3
downward and pull the saw blade 1 out.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one's health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
English | 17
Dr. Eckerhard Strötgen
Head of Product
Certification
1 609 929 N65 | (29.1.08)