Carat DustCatch 125 Laser Instrucciones De Manejo página 6

The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times the tool is switched off or when it is running
but not actually operating. This may significantly reduce the
exposure level over the total working period.
Laser
The interchangeable equipment is suited with a laser. When
switched on the laser projects a red line on the surface to be grinded.
The visibility of the laser can be increased by wearing special 'laser'
goggles, contact your Carat dealer for information.
Don't stare into the beam!
Laser class 2
< 1 mW, 635‐370 nm
Environment
Do not use this power tool in a dangerous environment. Do not use it
in an wet or clamp environment, such as rain. The working area must
be dry.
Mind (when working on floors, walls or sealing's) concealed electric
lines, gas and water pipes. Check your working area, e.g. with a
metal detector.
Failure to follow these instructions may result in electric shock, fire
and/or serious injury.
Main Parts Composed Power Tool
The main parts are numbered identical to the graphics of the
composed power tool at page 2 of this manual.
1. Assembly flanges (5 pair)
2. Screws (Assembly flanges, 2 pieces)
3. Guard and extraction hood
4. Screws (Guard and extraction hood, 4 pieces)
5. Inner guard
6. Depth locking
7. Cover
8. Clamping nut [*]
9. Diamond grinding wheel [*]
10. Spacer
11. Mounting flange [*]
12. Grinder spindle [*]
13. Vacuum connection
14. Vacuum hose
15. Spindle lock button [*]
16. ON/OFF‐switch [*]
17. Auxiliary handle [*]
18. Laser
19. Two‐pin spanner for clamping nut [*]
[*] Isn't a part of the DustCatch guard and extraction hood.
3. ASSEMBLY INSTRUCTIONS
Pull the mains plug of the power tool from the socket, before any
work on the machine itself!
It's recommended to wear worker's gloves while assembling or
changing the diamond grinding wheel.
Diamond grinding wheels become very hot due operating. Don't
touch them until they have cooled down.
Diamond grinding wheel
This composed power tool is not intended to be used in combination
with other tools than diamond grinding wheels. The guard doesn't
ENGLISCH – ORIGINAL INSTRUCTIONS |
supply suitable protection for tools other than diamond grinding
wheels.
The arbor of the diamond grinding wheel must fit the mounting
flange. Do not increase the arbor of the diamond grinding wheel. Do
not use reducers or adapters.
The permissible speed (rpm) of the diamond grinding wheel used
must be at least the speed stated on the nameplate of the used
grinder.
Always select a diamond grinding wheel suitable for the specific
material to be grinded. We advise diamond grinding wheels from
Carat. Observe the manual of the grinding wheel.
Make sure the diamond grinding wheel is rotating in the correct
direction. Verify the direction of the arrow on the diamond grinding
wheel is corresponding the direction of the arrow on the power tool.
Mounting the interchangeable equipment
The guard and extraction hood comes with 5 pair assembly flanges
and is suitable to be mounted on several grinders, see section
"Technical Data".
Never use assembly flanges which are not suitable for the selected
grinder. On each pair of assembly flanges is stated for which grinder
they are suitable. At the first part the brand and a unique number are
engraved, on the second part only the unique number is engraved.
 Remove the original guard, mounted on the power tool. Observe
the operating instructions of the grinder, where the
interchangeable equipment will be mounted on.
 Remove the clamping nut [8] and the mounting flange [11] from
the power tool where this interchangeable equipment will be
mounted on.
 Clamp the two parts [1] of one pair assembly flanges around the
flange of the grinder. If necessary (not for a Metabo grinder)
tighten the two screws [2], as illustrated on page 2, figure A. Mind
that the assembly flanges fit on way, the engraved text must point
outwards.
 Loosen the three cylindrical screws which mount the cover [7] on
the guard and extraction hood [3] with the aid of a screwdriver.
 Loosen the depth locking [6].
 Remove the cover from the guard and extraction hood.
 Mount the guard and extraction hood on the assembly flanges en
tighten the four screws [4], illustrated on page 2, figure A.
 Mount the auxiliary handle [17] supplied with the grinder, parallel
to the diamond grinding wheel, as illustrated.
Mounting the diamond grinding wheel
To change the diamond grinding wheel the guard and extraction
hood must be swiveled out. Place the power tool on a firm surface.
 Clean the mounting flange, spacer and clamping nut.
11