Technical Data; Intended Use - Festool TURBO II M - 8 WP R1 Manual De Instrucciones

3

Technical data

Exhaust turbine
Power supply (input)
Mains frequency
Power consumption
Fuse
Compressed air supply
Max. volume flow (air)
Nominal volume flow (admission rate 20 m/s)
Max. vacuum in normal operation
Max. vacuum in the event of a fault (e.g. power failure)
Sound pressure level as per EN 60704-1 and uncertainty
K (at 40 Hz) *
Filter surface area
Dimensions (LxWxH)
Container capacity
Weight
Dust extraction, diameter of connection pipes
Protection category
Permissible ambient temperature in operation
Relative humidity
Residual dust content in circulating air
ATEX identification
EC-type examination certificate number
* The values mentioned are emissions values and
do not necessarily correspond to the standard of
work. In fact, there is a correlation between the
emissions and exposure values, but these cannot
be used reliably to determine whether further pre-
cautionary measures are unnecessary. Factors
which influence the actual level of exposure of the
workers include features of the workspace, other
sources of noise, etc., for example the number of
machines and other neighbouring work. The per-
missible exposure level may vary from country to
country. Using this information the user of the ma-
chine can make a better assessment of the dangers
and risks.
4

Intended use

The exhaust turbine
Turbo II M - 8 WP R1/ - 14 WP R1
– corresponds to dust class 'M' according to IEC/
EN 60335-2-69 App. AA and is suitable for ex-
tracting hazardous dust with occupational expo-
Turbo II M- 8 WP R1 Turbo II M- 14 WP R1
400 V 3~
50/60 Hz
7.5 kW
6 - 10 bar, not oiled
850 m
565 m
-180 hPa
-400 hPa
65 dB(A)
4 dB
4.8 m
1045 x 805 x 1740 mm
306 kg
100 mm
IP 5x / IP 64 (ATEX)
0 - 45 °C
Max. 90%
< 0.1 %
CE 0637 II 3D Ex tc IIIC T135 °C Dc
0 °C ≤ Ta ≤ 45 °C X
IBExU14ATEXB007 X
sure limit values ≥ 0.1 mg/m³ as well as wood and
paint dust,
– designed exclusively for industrial use.
– Extracting dust with a Kst value > 200 (bar*m)/s
and/or an ignition energy < 10 mJ is not permit-
ted. Please observe local regulations.
– not suitable for extracting liquids.
Turbo II M - 8 WP R1/ - 14 WP R1 ATEX
– corresponds to dust class 'M' according to IEC/
EN 60335-2-69 App. AA and is suitable for ex-
tracting hazardous dust with occupational expo-
sure limit values ≥ 0.1 mg/m³ as well as wood and
paint dust,
– is suitable for absorbing and extracting dry, com-
bustible and conductive dust at machines and de-
vices in Zone 22,
– designed exclusively for industrial use,
– suitable up to a total dust load of 160 g/min (8WP)
and 280 g/min (14WP).
– not suitable for extracting liquids.
Turbo II M
400 V 3~
50/60 Hz
16 A
6 - 10 bar, not oiled
3
/h 1230 m
3
/h 565 m
- 180 hPa
- 400 hPa
66 dB(A)
2
1045 x 805 x 1740mm
50 l
316 kg
100 mm
IP 5x / IP 64 (ATEX)
0 - 45 °C
Max. 90%
< 0.1 %
GB
11 kW
32 A
3
/h
3
/h
4 dB
2
7.2 m
50 l
19