JB Systems CD 670 Manual De Instrucciones página 6

ENGLISH
 PAUSE MODE: normally the JOG WHEEL is used to search very precisely (1frame
precision) for the exact cue point. When the fast search mode is turned on, you can
use the JOG WHEEL to search very quickly forward/backward inside the current
track.
16. LCD DISPLAY: Shows all important information needed during playback. Refer to the
next chapter for more information.
17. SGL/CTN button: You can choose between "single track mode" and "continuous
play".
 Continuous play: the complete CD will be played without interruption. (mostly used
in pubs)
 Single track: player stops at the end of each track and waits at the beginning of the
next track. (mostly used by deejays)
Push the SGL/CNT button for more than 1second to switch between normal and "auto
cue" mode. In "auto cue" mode the player waits at the first music note of each track.
This means that badly indexed CDs will not interfere with the instant start capabilities
of this CD player. This is a very useful feature for deejays!
18. TIME Button: The TIME button switches between elapsed playing time, remaining
time in a selection and total remaining time of the disc. (standard = remaining /track)
19. FADER START Sockets: If you are using a mixer with fader start function, connect
the player with the fader start of the mixer. Please note that these sockets must never
be connected with any voltage.
Attention: This remote control is only compatible with certain (Synq
20. CONTROL CONNECTOR: Connect the main unit here, using the supplied mini-DIN
cable.
LCD DISPLAY:
1. PLAY: appears while the unit is playing a CD.
2. PAUSE: appears while the player is in pause or cue mode.
3. CUE: appears when the CD-player wait at the cue point.
JB SYSTEMS®
OPERATION MANUAL
® ®
or Pioneer compatible) mixers.
7/67
ENGLISH
4. ELAPSED, TOTAL REMAIN: indicates that the time shown on the display is the track
elapsed, remaining or total remaining time.
5. TIME BAR: shows either time remaining or elapsed depending on the setting of the
TIME button. Starts flashing at the end of each track to alert the user to take action.
6. BPM/PITCH DISPLAY: (see PITCH button(11) and TAP button(10) to learn how to
switch between the 3 display modes)
 BPM indicator ON: the automatic beat counter shows the number of Beats Per
Minute on the display.
 BPM indicator BLINKING: the manual beat counter shows the number of Beats
Per Minute you manually "tapped" on the display.
 PITCH indicator ON: The display shows the actual speed variation (in %)
compared to zero pitch.
7. AUTO CUE: appears when the "auto cue" function is active. See SGL/CTN-button(17).
8. SINGLE: appears when the unit is set to play just one track at a time. When it is not
shown, the CD plays continuously through all tracks. The function is controlled by the
SGL/CTN button(17).
9. LOOP: shows when a loop is playing.
10. RELOOP: shows when a loop is programmed so you can use the reloop button.
11. TRACK: Shows current track number.
12. MINUTE: Shows "minutes" time information of current track.
13. SECOND: Shows "seconds" time information of current track.
14. FRAME: Shows "frame" time information of current track. (1 frame = 1/75
15. ANTI SHOCK AND BUFFER INDICATOR: Shows the status of the anti shock
memory.
HOW TO USE ...
Most of the common functions are explained in the previous chapter "controls and
functions" In this chapter we talk about the functions that need a little more explanation.
SOME GENERAL FUNCTIONS:
 SLEEP MODE:
The CD player automatically shuts off the transport and laser after about 15 minutes
(when in pause or cue mode). This extends the life of your motor drive and laser. During
sleep mode the display shows the word "SLEEP". To wake up the player, just press the
cue or play button, the display turns to normal and is ready to receive instructions.
 RELAY FUNCTION:
First open the 2 faders of the CD inputs on your mixer. Press the RELAY button to
enable the relay function, the relay LED turns on. Put a disc in both players and start
playback on one of the units. Alternately a track will be played from both units until the
relay function is disengaged. You can always put a new CD in the player that is waiting
in pause. In this way you can create an endless program, perfect for use in pubs etc.
NOTE: by switching on the relay function you automatically put both players in single mode.
 PITCH BENDING:
This function is used to synchronize the beats of two tracks. This can be done in two
ways:
CD670 JB SYSTEMS®
OPERATION MANUAL
th
sec.)
8/67 CD670