Bauknecht DBHBS 92C LT X Instrucciones De Uso página 75

1.2.2 INSTRUCTIONS FOR MANUAL CONFIGURATION (FIRST USE) - MICRO ACCESS POINT METHOD
This procedure uses Micro Access Point technology and can be used with routers that do not support WPS.
1. Before starting the configuration procedure, note the name (SSID) and password of the home wireless network and the SAID
code of the device. This information will be needed during the installation procedure.
2. Turn the router on, check that the internet connection is active and connect your smartphone/tablet to your Wi-Fi network.
3. On the device, activate the recognition process by pressing the connectivity key for 5 seconds (two acoustic signals will be
emitted as confirmation, the first after 3 seconds, the second after 5 seconds) • the Wi-Fi network icon should start flashing on
the device's interface.
4. Scan the QR code shown on the label attached to the device; at this point, the Bauknecht Home Net app will provide detailed
instructions on how to carry out the procedure. Note: In some cases, the app may ask you to specify the type of device: in this
case, select Hood
5. Once the connection has been made, the Wi-Fi icon on the device should stop flashing and remain continuously lit. If not,
disconnect and then reconnect the device to the mains power and repeat the procedure.
6. The configuration procedure is complete.
1.3 SWITCH OFF / ON WI-FI FEATURE
To switch off the connection of the appliance to the wifi network, press and hold for 5 seconds the connectivity button on the
appliance (one acoustical feedback is played). The wifi icon on the appliance display should turn off.
To turn on again the wifi connection on the appliance, press the wifi button on the remote control.
When appliance is provisioned, user can disengage this function and disconnect it from the wifi network by pressing and hold for 10
seconds the connectivity button on the appliance (two acoustical feedbacks are played, one after 5 seconds, one after 10 seconds).
The wifi icon on the appliance display should turn off.
To connect the appliance again to the home wifi network follow the procedure on paragraph "provisioning".
1.4 REMOTE CONTROL / DAILY USE
This feature may be implemented depending from the appliance type.
1. Make sure the Your router is ON and connected to the Internet.
2. Make sure the WiFi Connection State indicator status on the product's display is solid.
3. Use the Bauknecht Home Net App to control the appliance by remote, so You can:
• check your appliance and activate options also when you are out of home.
• access additional functions, for instance the smart energy mode.
• optimize energy consumptions leveraging for example the best energy tariff.
• access further information on best use of your appliance.
• receive feedback about appliance status in case of alarms.
1.5 QUICK IDENTIFICATION OF APPLIANCE CONNECTION STATE
If WiFi Connection State indicator on appliance display blinks fast, then Appliance is searching connection to router. If it blinks
slowly, then Appliance is connected to router but it is not able to connect to internet (for example ADSL not working) some appliance
type doesn't support slow blinking but only blinking feature.
If solid ON Appliance is connected to internet and to the Whirlpool's cloud system.
1.6 WIFI FAQs
Which WiFi protocols are supported?
The WiFi adapter installed supports WiFi b/g/n for European countries.
Which settings need to be configured in the router software?
The following router settings are required: 2.4 GHz enabled, WiFi b/g/n, DHCP and NAT activated.
Which Version of WPS is supported?
WPS 2.0 or higher. Check the router documentation.
Are there any differences between using a smartphone (or tablet) with Android or iOS?
You can use whichever operating system you prefer, it makes no difference.
Can I use mobile 3G tethering instead of a router?
Yes, but cloud services are designed for permanently connected devices.
How can I check whether my home Internet connection is working and wireless functionality is enabled?
You can search for your network on your smart device. Disable any other data connections before trying.
How can I check whether the appliance is connected to my home wireless network?
75