Metabo HPT SV 13YST Manual De Instrucciones página 5

4. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
5. Use right tool.
Don't force small tool or attachment to do the job of a
heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
6. NEVER use a power tool for applications other
than those specifi ed.
NEVER use a power tool for applications other than
those specifi ed in the Instruction Manual.
7. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool. Never
allow the tool to be operated by children, individuals
unfamiliar with its operation or unauthorized
personnel.
8. Keep all screws, bolts and covers tightly in
place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
9. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
10. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure and
tight.
11. Keep motor air vent clean.
The tool's motor air vent must be kept clean so that
air can freely fl ow at all times. Check for dust build-up
frequently.
12. Operate power tools at the rated voltage.
Operate the power tool at voltages specifi ed on its
nameplate.
If using the power tool at a higher voltage than the
rated voltage, it will result in abnormally fast motor
revolution and may damage the unit and the motor
may burn out.
13. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metabo HPT authorized service center.
14. NEVER leave tool running unattended. Turn
power off .
Don't leave tool until it comes to a complete stop.
15. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
16. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.
18. NEVER leave the random orbit sander on fl oor and
so on while spinning.
19. NEVER apply water or lubricating oil, otherwise
hazards from electrical shocks may result.
20. NEVER push the random orbit sander too strongly
onto a surface.
Pushing the random orbit sander too strongly may
cause the sanding paper to tear or shorten the life of
the sander itself.
21. ALWAYS operate the random orbit sander safely for
correct use.
This random orbit sander is a portable dry plane
surface sander that was designed for fi nishing wood
and metal surfaces and ground coats.
22. ALWAYS securely installing the sanding paper.
23. ALWAYS wear a protective mask when operating the
random orbit sander.
Ventilate your work area adequately when you
perform sanding operations.
24. Defi nitions for symbols used on this tool
V ..................volts
Hz ................hertz
A ..................amperes
n
................no load speed
o
W .................watt
.................Class II Construction
---/min ..........revolutions per minute
................Alternating current
In the following cases, clean the dust bag and fully remove
any dust.
Dust remaining in the dust bag may cause ignition.
● Sanding steel sheets after sanding materials such as
wood
● After completing sanding work
Do not throw sanding dust on an open fi re because
materials in fi ne particle form may be explosive:
English
5