Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
For the safety of the child the following checks
should be made before every trip:
• The safety seat is firmly installed in the vehicle.
• The straps are not twisted.
• The safety seat straps are firmly fastened around
the child's body, without squashing it.
• The shoulder straps
(10)
are correctly adjusted
and not twisted.
•
The shoulder protectors (3)
are on a level with the
child's shoulders.
•
The clasps (5)
are correctly inserted into the belt
buckle (6).
6. car seat installation. grouP 1
GROUP 1 only. From 0 to 12
notice
months approx. (0 - 13 kg).
1. Ensure that the seat is not in a reclined position.
Pull the lever
(15)
forward and adjust the angle of
recline to position 1 without releasing the lever.
Release the lever when the seat is in the desired
position (fig. 18).
2. Place the seat in the back seat of the vehicle in the
direction of travel (fig. 19).
3. Take out the reducer cushion (4). Pass the
abdominal strap of the seat belt through the
(11)
lower seat guides
and underneath the seat.
Buckle the vehicle seat belt until you hear a
click (fig. 20).
28
fig. 18
fig. 19
1
2 3 4
(11)
Abdominal
fig. 20
belt guides
(group
0/1/2/3).
11
11
click
4. Pass the diagonal section of the vehicle´s belt
through the rear side of the backrest cushion and
the seat backrest.
5. And continuing, pass the diagonal section of
the vehicle´s belt between the backrest and the
headrest sides fig. 20).
6. Make sure it is as tight fitting as possible. Ensure
the straps are not twisted or knotted at any point.
For the safety of the child the following checks
should be made before every trip:
• The safety seat is firmly installed in the vehicle.
• The straps are not twisted.
• The safety seat straps are firmly fastened around
the child's body, without squashing it.
(10)
• The shoulder straps
are correctly adjusted
and not twisted.
•
The shoulder protectors (3)
are on a level with the
child's shoulders.
•
The clasps (5)
are correctly inserted into the belt
buckle (7).
7. Placing the child in the seat. grouP 1
To seat the child correctly follow the steps described
in section 5.
8.installing the child seat. grouP 2 and 3
GROUP 2/3 only. From 4 to
notice
12 years aprox. (15- 36 kg).
1. Make sure the 5-point harness and harness buckle
have been correctly removed (see points 3.5).
2. Follow the steps described in section 3.10.
3. Place the safety seat on the vehicle seat in the
direction of travel.
4. Place the child in the seat. Pull the vehicle safety
belt and pass it in front of the child until it reaches
the vehicle seat belt buckle.
IMPORTANT! Make sure the belt is not twisted.
5. insert the clasp into the vehicle seat buckle. You
should hear a click.
6. Place the diagonal part of the belt
(27)
and the part
that crosses the lap
(28)
on the side of the vehicle
safety seat buckle, through the abdominal belt
(11)
guide
of the safety seat (fig. 21 B).
(27)
7. Pass the diagonal part of the belt
through the
(2)
diagonal belt guide (group 2/3)
on the headrest
until it is fully extended and not twisted (fig. 21 A).
8. Make sure the diagonal part of the belt passes
over the child's collar bone and not the neck.
iMPortant! The part of the abdominal belt
should rest as low as possible over the child's hips, on
both sides.
tiP: if the seat back covers the guide
(2)
you can
raise the headrest, which will allow you to insert the
diagonal section of the belt easily. You should then
reset the headrest to the correct height, as shown in
point 3.11.
(28)
29
Publicidad
Tabla de contenido
