Operating Instructions; Boxing In; Door Reversal; Panel Changing - Vitrifrigo Trivalente Digit Serie Manual De Uso

User, Maintenance and Installation Manual - Trivalenti

Operating Instructions

!
R
Follow the instructions below with
great care.
R
It is strictly forbidden to install the refrigerator using
different methods to those described in this manual,
or persons who have not been authorised by
Vitrifrigo snc.
R
To avoid possible damage, only insert screws in the
relevant holes provided on the refrigerator.
R
Make sure that electrical cables are adequately
protected - especially the power cables - in order
to avoid them coming into contact with hot or sharp
parts.
R
Vitrifrigo snc refuses to accept any liability for
installations carried out by personnel who have not
been authorised by the company itself.

BOXING IN

The refrigerator must be inserted into a compartment of
adequate dimensions (see Table 3) – without forgetting that there
must be an all-round gap of no more than 3 mm between the
appliance and the compartment. Ensure that the compartment
is:
þ
perfectly regular and with a flat bottom for problem-free
appliance slotting in or removal;
þ
sufficiently sturdy to sustain the weight of the refrigerator
when full, taking into account the stresses caused by the
vehicle when it is in motion.
Before inserting the refrigerator into the compartment, fix strips to
the sides "A" (as in Fig.4) using an elastic bonding agent.
Insert the appliance into the compartment, ensuring that it is
perfectly aligned and that nothing protrudes. Also make sure that
there is a gap of 10-20 mm between the vehicle wall and the
refrigerator unit in order to permit the correct ventilation of this
latter (see Fig. 4).
Use screws to fix the refrigerator firmly to the sides of the
compartment "A" (as in Fig. 5). The screws should be suited to
withstand strain, not forgetting the stresses caused by the vehicle
in motion and should be inserted in the holes "B" made inside the
unit (as in Fig.5). Use the cap supplied to close the holes "C" (as in
Fig. 5).

DOOR REVERSAL

To change the direction in which the appliance door opens, from
right to left, it is necessary to adjust the hinges "B" (Fig.1) and the
doorstop "C" (Fig.1) as follows:
Disassemble the doorstop "C" by removing the screw "A" (see
Fig.5),
Loosen the screw pin "D" on the top hinge "B" (see Fig.5),
Move the door upwards until it comes away from the hinge.
Loosen the screw pin "D" on the bottom hinge "B" and screw it
into the bottom hinge on the opposite side,
Reposition the door and screw the screw pin into the top hinge
on the opposite side,
Replace the doorstop "C" and tighten into place with the screw.

PANEL CHANGING

To disassemble and/or change the panel "A" (Fig.1), proceed as
follows:
þ
Remove the door, as indicated in the previous section.
þ
Loosen the screws on the lower base section and remove
it.
þ
Slide the panel out downwards.
þ
Insert the new panel in place of the old one, sliding it
upwards until the stop.
þ
Reassemble the lower base section.

ELECTRICAL CONNECTION

All cables must be inserted into the connectors "P" (Fig.1) as
shown in Fig.10, making sure that the screws are properly
tightened and ensuring that the connection has been made
perfectly.
Check that the voltage used corresponds to that printed on the
appliance rating label.
The connection between the refrigerator and the battery must be
made directly using a cable with a minimum section of 1.5 mm if
the length of the cable is less than 4 metres; 2.5 mm if the cable
length is between 4 and 9 metres; 4 mm if the cable length is more
than 9 metres.
WARNING: ALWAYS RESPECT POLARITY (for DC connections).
Power Supply (MAINS POWER)
Insert the power cables into the connector "1" (Fig.10). Use a
cable with a section of at least 1.5 mm
thermomagnetic circuit breaker in compliance with the standard
and regulations in force.
Power Supply (BATTERY)
Power supply with double line (direct and switch block) (See
Fig.10-A)
Connect the direct power cable (respecting the polarities) to
the connector "3" and connect the power cable from the
switch block (respecting the polarities and sections as
previously indicated), to the connector "2"
Direct power supply: (see Fig.10-B)
Connect the power cable (respecting the polarities and
sections as indicated previously) to the connector "3".
Connect the connector "5" to connector "2" creating an
electric jumper, using a conductor that has a section of no less
than 1.5 mm
2.
Power Supply for the EXTERNAL FAN (optional)
Connect the fan power cable (respecting polarities) to the
connector "4" (Fig.10) using a cable with an adequate section
for the power of the fan.
GAS CONNECTIONS
This refrigerator is able to operate using gas (propane or butane
LPG). The gas type and operating pressure must be the same as
those indicated in the box "7" (Fig.2) on the rating label "E" (Fig.1)
inside the refrigerator, or on the Conformity Declaration attached
to this manual.
Installation must be carried out in accordance with the various
13
2
2
2
2.
Fit a differential
.