Transportation And Storage; Cleaning And Maintenance - MSW MULTI-GRIN135.1 Manual De Instrucciones

VIII. MACHINE OPERATION – BASICS
Before using the device, make sure the required attachment or flexshaft (MULTI-GRIN135.1 (6240), MULTI
-GRIN135.3 (6242), MULTI-GRIN135.4 (6243)) is connected firmly and securely to the clamp. Check
regularly whether the clamp is sufficiently tight. Do not turn the device on or off if the attached tool is in
direct contact with the workpiece - bring the device closer to the workpiece once it reaches its pre-set
speed. To adjust the speed, use the knob on the back of the housing. Use lower revolutions for polishing and
buffing, higher for drilling and etching. If in use for longer periods, make regular breaks to avoid overheating
the device. Before drilling on metal, mark your drill location.
1 2 3
Replacing attachments
When replacing accessories, disconnect the grinder from the power supply. In order to change tools, press
the locking button next to the clamp, unscrew the cap (by hand or using the attached wrench), then remove
the attached tool and sleeve, select the right sleeve for the new tool, insert it and screw on tightly. When
changing tools on the flexshaft (MULTI-GRIN135.1 (6240), MULTI-GRIN135.3 (6242), MULTI-GRIN135.4
(6243)) use the supplied wrench – it works on a similar principle to the locking button. Use the wrench to
lock the clamp, replace the tool and screw it back tightly.
If assembling fabric disks with no permanent stem attached, screw a threaded shaft onto the opening in the
middle of the disk.
If attaching disks with no permanent stem, select a shaft of an appropriate diameter, onto which the disk will
fit snugly, unscrew the locking bolt, place the disk between the gaskets and tighten the locking bolt using the
wrench.
10
Machine description
1. Mounting handle
2. Rotating adjustment knob.
3. Lock buton
4. Clamping bracket with nut
4 5
5. Replaceable end
Rev. 05.05.2017
Mounting the flexshaft (MULTI-GRIN135.1 (6240), MULTI-GRIN135.3 (6242), MULTI-GRIN135.4 (6243)):
In order to mount the flexshaft, analogous to when replacing tools, press the button which locks the clamp
and attach the shaft the right way around to the device. Then tighten the shaft plastic to the device, unfold
the shaft and turn the device on to maximum revs so that it runs without load for a few minutes.
Selecting tools
Select the appropriate tool for your task. Depending on your set, the grinder comes with drill bits, tools for
polishing, sandpapers of various weights, polishing disks, etc. Remember to use PPE (gauntlets, goggles, etc.)
when using the device.
IX. TRANSPORTATION AND STORAGE
During transport, the machine should be protected from shaking, crashing and turning upside down. Store it
in a properly ventilated place with dry air and without any corrosive gas.
X. CLEANING AND MAINTENANCE
• Disconnect the machine from the electricity when cleaning it.
• Use cleaner without corrosive substances to clean surface.
• After cleaning, all parts should be able to dry before the machine is to be reused
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
• Never spray the device with water jets.
XI. CHECK REGULARLY THE DEVICE
Check regularly whether the device is damaged. If it should be damaged, please stop using it immediately and
contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, take a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. The more detailed your information, the better the
customer service will be able to solve your problem rapidly and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to
a loss of warranty!
Rev. 05.05.2017
11