Battery Charge Indicator; Changing The Tool; Method Of Operation; Starting Operation - Bosch GDR 18V-200 C Professional Manual Original

16 | English
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Observe the notes for disposal.
Removing the Battery
The battery (6) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (7) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (6), press the release button (7) and
pull the battery out of the power tool. Do not use force to
do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface .
Note: The state of charge of the battery is also displayed on
the user interface Status indications.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
160992A5UW | (14.07.2020)

Changing the Tool

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Regularly clean the power tool's air vents. The motor's
u
fan can draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Use application tool: GDR/GDX 18 V-200 C (see figure
A – B)
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder up to the stop and release the locking
sleeve (2) to lock the application tool.
Impact-proof screwdriver bits (17) can be inserted using a
universal bit holder with ball catch (16).
Impact-proof screwdriver bits (17) can be inserted using a
universal bit holder with ball catch (16).
to
Use application tool: GDX/GDS 18 V-200 C (see figure
B – C)
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
plication.
Slide the application tool (18) onto the square drive of the
tool holder (1).
Due to the way the system operates, the application tool
(18) will move around slightly in the tool holder (1); this has
no influence on the function/safety.
Some application tools (e.g. double bits) cannot be safely
secured in the tool holder.
Capacity
Removing
60−100 %
Pull the locking sleeve (2) forward and remove the applica-
30−60 %
tion tool.
5−30 %
Operation
0−5 %

Method of Operation

The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in and tightening (impact mechanism in action).
Capacity
The impact mechanism is activated as soon as the screwed
80−100 %
connection runs tight and load is therefore put on the motor.
60−80 %
The impact mechanism then converts the power of the mo-
tor to steady rotary impacts. When loosening screws or nuts,
40−60 %
the process is reversed.
20−40 %
5−20 %

Starting Operation

0−5 %
Inserting the Battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Bosch Power Tools