Releasing The Cutting-Means Assembly; Cutting Height Adjustment; Quick Flip" Knobs; Quick Flip" Release Levers - Stiga 100 Combi 3 EL QF Manual De Uso

Ocultar thumbs Ver también para 100 Combi 3 EL QF:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 113
6. Complete the coupling by using the 
foot to rotate the quick release supports 
to the closed position (fig. 8.C) and 
insert the plug or split pin (fig. 8.D).
4.2.5 Assembling the canvas guard
1. Insert the two coupling hooks (fig. 11.A), 
found at the ends of the support chassis 
(fig. 11.B) inside the guide pins (fig. 11.C).
2. Position the support chassis (fig. 12.A) 
under the device (fig. 12.B), and fasten 
in place with the two screws (fig. 12.C).
4.2.6 Coupling to the accessory
lifting device
The cutting-means assembly is coupled 
to the accessory lifting lever (fig. 13.A) of 
the main machine by means of a spring 
and chain and a snap-on hook.
The snap-on hook (fig. 13.B) is used for the 
working position and can be moved between 
the chain links to adjust the lifting force.
4.2.7 Connecting the power
cable connector
Connect the connector (fig. 14.B) 
to the socket (fig. 14.A).
4.3 RELEASING THE CUTTING-
MEANS ASSEMBLY FROM
THE RIDE-ON MOWER
To release it correctly, follow the 
steps below in the same order.
1. Disconnect the machine cable (fig. 14.B).
2. Disconnect the chain from the "accessory 
lifting lever" (fig. 13.A) releasing 
the snap-on hook (fig. 13.B).
3. Remove the canvas guard by 
undoing the screws (fig. 12.C)
4. Disconnect the plug or split pin (fig. 8.D) 
and rotate the quick release supports 
to the open position (fig. 7.A).
5. Loosen and release the
transmission belt as follows:
• 4WD models
– Use the left hand to grasp the tensioner 
lever (fig. 9.A) and pull it outwards.
– Use the right hand to remove the 
belt from the pulley (fig. 9.C).
– Extract the belt from the 
machine pulley (fig. 9.B).
• 2WD model
– Use the left hand to grasp the tensioner 
lever (fig. 10.A) and pull it outwards.
– Use the right hand to remove the 
belt from the pulley (fig. 10.C).
– Extract the belt from the 
machine pulley (fig. 10.B).
6. Raise the quick release support coupling 
brackets (fig. 7.B) and separate the 
cutting-means assembly from the 
ride-on mower with front deck.
5. CONTROLS

5.1 CUTTING HEIGHT ADJUSTMENT

Always perform adjustments when
the cutting means are stationary.
5.1.1 Electric cutting height adjustment
The cutting height is adjusted in 
infinitesimal mode, enabling the electric 
cutting height adjuster switch found 
on the front deck ride-on mower.
The cutting height indicator (fig. 1.H) 
shows the adjusted height.
IMPORTANT To enable the electric adjustment
it is necessary to connect the cutting-means
assembly electric cable connector to the socket
(fig. 14.A) found on the front deck ride-on mower.

5.2 "QUICK FLIP" KNOBS

The "Quick Flip" knobs (fig. 1.E) are used to 
release the rear section of the cutting-means 
assembly from the support arms and lower it.
From this position it is possible to lift the 
cutting-means assembly to the maintenance 
and wash position (chap. 7.2);

5.3 "QUICK FLIP" RELEASE LEVERS

The "Quick Flip" release levers (fig. 1.F) 
make it possible to quickly lower the cutting-
EN - 6

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

100c e qf

Tabla de contenido