Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
sPECIfIC sAfETy RulEs
• W ear ear protectors. Exposure to noise can
cause hearing loss.
• U se auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• H old power tools by insulated gripping surfaces,
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
• K eep hands away from all cutting edges and
moving parts.
• M aintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• W ARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause can-
cer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cifically designed to filter out microscopic particles.
symbology
Double Insulated
Volts
Alternating Current
A
Amps
No Load Revolutions per
Minute (RPM)
Seal of Electrical Security
Read operator's manual
Wear hearing protection
Wear eye protection
EXTENsIoN CoRDs
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cord to make up the total length, be sure each cord
contains at least the minimum wire size required.
If you are using one extension cord for more than
one tool, add the nameplate amperes and use the
sum to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be
sure it is marked with the suffix "W-A" ("W" in Cana-
da) to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualified person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
or Extension Cords*
Nameplate
Amperes
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
READ AND SAvE ALL
INSTRUCTIONS FOR FUTURE USE.
fuNCTIoNAl DEsCRIPTIoN
8
1. Side handle
2. Clamping lever
3. Hammer/Drill
lever
4. Trigger
5. Lock button
6. Forward/Reverse
lever
7. Depth gauge
8. Chuck
16
Extension Cord Length
25'
50'
75'
18
18
8
18
18
18
18
18
16
18
16
14
16
14
12
14
12
10
12
10
--
7
3
2
4
1
100'
150'
18
16
16
14
14
12
12
12
10
--
--
--
--
--
6
5
Publicidad
Tabla de contenido
