Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS MANUAL
Leakage clamp meter
C-LOGIC 8730
Code: 301000056
ENGLISH
The meter is a portable, professional measuring instrument with LCD display for easy
reading by users. Measuring range switch is operated by single hand for easy operation
with overload protection and low battery indicator. It is an ideal multifunction meter for
professionals, factories, schools, fans and family use.
The meter is used for AC leakage current, AC voltage, DC voltage, resistance, capacitance,
circuit connection, diode and temperature test.
SAFETY INFORMATION
Warning
Be extremely careful when using this meter. Improper use of this device can result in
electric shock or destruction of the meter. Take all normal safety precautions and follow
the safeguards suggested in this manual. To exploit full functionality of the meter and
ensure safe operation, please read carefully and follow the directions in this manual.
The meter is designed and manufactured according to safety requirements of EN 61010-
1:2010, EN 61010-2-032, EN 61010-2-033 on electronic measuring instrument and hand
held digital multipurpose meter. The product meets with the requirements of 600V CAT III
and pollution degree 2.
All safety guidelines outlined should be followed otherwise the protection provided by the
instrument may be impaired.
Warning symbols in the manual alert users of potential dangerous situations.
Precautions are to prevent the user from damaging the instrument or the test object.
PRELIMINARY
• When using the meter, the user should comply with standard safety rules:
◦ General shock protection
◦ Prevent misusing the meter
• Please check for damage during transportation after receiving the meter.
• If the meter is stored and shipped under hard conditions, please confirm if the meter is
damaged.
• Probe should be in good condition. Before use, please check whether the probe insulation
is damaged and if the metal wire is bare.
• Use the probe table provided with the meter to ensure safety. If necessary, replace the
probe with another identical probe or one with the same level of performance.
USAGE
• When using, select the right function and measuring range.
• Don't measure by exceeding indication value stated in each measuring range.
• When measuring a circuit with the meter connected, do not contact with probe tip (metal
part).
• When measuring, if the voltage to be measured is more than 60 V DC or 30 V AC (RMS),
always keep your fingers behind finger protection device
• Do not measure voltage greater than 600V DC or AC(RMS).
• In the manual measuring range mode, when measuring an unknown value, select the
highest measuring range first.
• Before rotating conversion switch to change measuring function, remove probe from the
circuit to be measured.
• Don't measure resistor, capacitor, diode and circuit connected to power.
• During the test of currents, resistors, capacitors, diodes and circuit connections, be
careful to avoid connecting the meter to a voltage source.
• Do not measure capacitance before capacitor is discharged completely.
• Do not use the meter in explosive gas, vapor or dusty environments.
• If you find any abnormal phenomena or failure on the meter, stop using the meter.
• Unless the meter bottom case and the battery cover are completely fastened completely,
do not use the meter.
• Don't Store or use the meter in the conditions of direct sunlight, high temperature and
high humidity.
MAINTENANCE
• Don't try to open the meter bottom case to adjust or repair. Such operations can only be
performed by technicians who fully understand the meter and electrical shock hazard.
• Before opening the meter bottom case or battery cover, remove probe from the circuit to
be measured.
• To avoid wrong readings causing electric shock, when
replace the battery immediately.
• Clean the meter with damp cloth and mild detergent. Do not use abrasives or solvents.
• Power off the meter when the meter is not used. Switch the measuring range to "OFF"
position.
• If the meter is not used for long time, remove the battery to prevent the meter being
damaged.
REPLACING THE BATTERIES
To avoid electric shock, make sure that the test leads have been clearly move away from
the circuit under measurement before opening the battery cover.
Do not mix old new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc) batteries.
• If the sign "
• Loosen the fixing screw of the battery cover and remove it.
• Replace the exhausted batteries with new ones.
EN
• Put the battery cover back and fix it again to its origin form.
Note:
Do not reverse the poles of the batteries.
REPLACING TEST LEADS
Replace test leads if leads become damaged or worn.
Use meet EN61010-031 standard, rated CAT.III 600V, or better test leads.
ACCESSORIES
• Probe
• Thermocouple (K type)
• 1.5 AAA battery
• Short operation manual
appears on the meter display,
Warning
Warning
" appears, it means that the batteries should be replaced.
Warning
FULL MANUAL DOWNLOAD
You can download the complete
manual at the URL
http://www.c-logic.es/manuales
MANUFACTURER:
MGL EUMAN S.L.
Parque Empresarial de Argame,
C/ Picu Castiellu, Parcelas i-1 a i-4
E-33163 Argame, Morcin
Asturias, España (Spain)
1 pair
1 pc
2 pcs
1 pc
Publicidad
