Tabla de contenido
Publicidad
yourself from work and ground.
1.3 Disconnect input plug or power before working on
machine.
2
Breathing welding fumes can be hazardous to your
health.
2.1 Keep your head out of fumes.
2.2 Use forced ventilation or local exhaust to remove
fumes.
2.3 Use ventilating fan to remove fumes.
3
Welding sparks can cause explosion or fire.
3.1 Keep flammable materials away from welding.
3.2 Welding sparks can cause fires. Have a fire extin-
guisher nearby and have a watchperson ready to use
it.
3.3 Do not weld on drums or any closed containers.
4
Arc rays can burn eyes and injure skin.
4.1 Wear hat and safety glasses. Use ear protection and
button shirt collar. Use welding helmet with correct
shade of filter. Wear complete body protection.
5
Become trained and read the instructions before
working on the machine or welding.
6
Do not remove or paint over (cover) label.
2 GENERAL DESCRIPTION
2.1 SPECIFICATIONS
This manual has been prepared for the purpose of edu-
cating personnel assigned to install, operate and service
the welding machine.
The purchaser should address any complaints for los-
ses or damage to the vector. Please indicate the arti-
cle and serial number whenever requesting informa-
tion about the welding machine.
3 INSTALLATION
• Only skilled personnel should install the machine .
• All connections must be carried out according to cur-
rent regulations, and in full observance of safety laws.
3.1 PLACEMENT
Unpack the wire feeder and place it above the welding
machine, using the flexible rotating cylinder provided.
At the first start stage the operator must select the article he
wants to use.
Once the generator has been connected to the carriage by
means of the connector, the machine can be started.
The screen H of the wire feed carriage shows 3 flashing
lines; to select just push one of the 2 push-buttons N or O to
display the welder article you want to use.
4 DESCRIPTION OF CONTROLS
4.1 CONTROLS ON THE FRONTOF THE MACHINE.
A- Green LED.
Signals that the display H shows the current
HOLD
or voltage value measured during welding.
To display one of the two values, simply press one of the
two selection keys N or O.
A
B
C
D
E
F
G
T
B- Green LED.
Signals that the display H shows the pro-
PROGRAM
gram number being used.
Check the instructions posted inside the mobile side
panel for the diameter, wire type and gas corresponding
to the program number displayed. The figure on the dis-
play H is always preceded by the letter P.
C- Green LED.
Signals that the welding machine is in 4-
stage automatic mode.
When the LED is off the welding machine is in 2-stage
manual mode. Use the selection keys N and O to select
manual or automatic mode. The display H will show the
message 2t when the machine is in 2-stage manual
mode, or 4t when it is in 4-stage automatic mode.
If the welding machine is set to 2-stage manual mode,
welding begins when the button is pressed, and stops
when it is released.
If the welding machine is set to 4-stage automatic mode,
press the torch trigger to begin welding;
you may release the trigger once the procedure has
begun. Press and release the trigger again to stop weld-
ing. This setting is suitable for long-term welding, where
the welder may tire of holding down the torch trigger.
D - green wire feed test LED.
It signals that wire feeding function is active.
To feed wire simply press the torch trigger
and adjust the output speed using the potentiometer P. If
the Push-Pull welding torch is used the output speed is
adjusted by means of the up-down triggers on the weld-
ing torch grip. When the H LED is lit, the display shows
the speed in meters per minute.
H
M
L
I
N
O
P
V
U
7
Publicidad
Tabla de contenido
