Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts; Carbon Brushes; Notes On Environmental Protection / Disposal - Gardol GEK-E 2240 Manual De Instrucciones

Ocultar thumbs Ver también para GEK-E 2240:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
9. Cleaning, maintenance and
ordering of spare parts
Danger!
Always disconnect the mains plug before
cleaning the chainsaw.
Never immerse the unit in water or other li-
quids in order to clean it.
Store the chainsaw in a safe and dry place
out of the reach of children.
9.1 Cleaning
Regularly clean the clamping mechanism by
blowing it out with compressed air or cleaning
it with a brush. Do not use tools for cleaning.
Keep the handles free of grease so that you
can maintain a firm grip.
Clean the device as required with a damp
cloth and, if necessary, mild washing up li-
quid.
If the chainsaw is not to be used for an exten-
ded period of time then you should remove
the chain oil from the tank. Briefly immerse
the saw chain and the cutter rail in an oil bath
and then wrap them in oil paper.

9.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
9.3 Maintenance
Replacing the saw chain and cutter rail
The cutter rail needs to be replaced if
the guide groove of the cutter rail is worn;
the nose sprocket in the cutter rail is dama-
ged or worn.
Proceed as described in the section "Assembly of
the cutter rail and the saw chain".
Checking the automatic chain lubrication
You should check the operation of the automatic
chain lubrication system on a regular basis in or-
der to guard against overheating and the associ-
ated damage to the cutter rail and the saw chain.
To do this, point the tip of the cutter rail towards a
smooth surface (board, section of a cut tree) and
allow the chainsaw to run.
If an increasing oil trace becomes evident during
this process then the automatic chain lubrication
system is working properly. If no clear oil trace is
Anl_GEK_E_2240_Teil1_SPK7.indb 26
Anl_GEK_E_2240_Teil1_SPK7.indb 26
GB
evident then please refer to the corresponding
instructions in "Troubleshooting". If the information
contained there still fails to remedy the situation
then please contact our service department or
another similarly qualifi ed workshop.
Danger! Do not actually touch the surface with
the tip of the cutter rail when performing this test.
Keep a safe distance (approx. 20 cm).
Sharpening the saw chain
Eff ective working with the chainsaw is only pos-
sible if the saw chain is in good condition and
sharp. This also reduces the risk of kickback.
The saw chain can be re-sharpened by any dea-
ler. Do not attempt to sharpen the saw chain your-
self unless you have the necessary special tools
and experience.

9.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
10. Notes on environmental
protection / disposal
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 26 -
09.12.15 10:31
09.12.15 10:31

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

45.017.41

Tabla de contenido