Know Your Product; Operation - SPARKY heavyDuty MKL 755CE Instrucciones De Uso

▪ A power source with a voltage greater than
that specified for the tool can result in serious
injury to the user, as well as damage to the
tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than
the nameplate rating is harmful to the motor.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out.
▪ The outer metal parts and the bits may get hot
after continuous operation. Do not touch the
bit or the work piece immediately after opera-
tion - they may be extremely hot and you may
get serious burns.
▪ Keep your hands away from the rotating bit.
▪ Use clamps or a vice to secure your work
whenever possible.
▪ Always switch off the machine and wait until
the spindle has come to a complete standstill
before placing it down.
▪ Do not force the machine: let the tool do the
work at a reasonable speed. Overloading will
occur if too much pressure is applied and the
motor slows resulting in inefficient work and
possible damage to the motor.
▪ Rags, cloths, cord, string and the like should
never be left around the work area.
▪ Before using the tool on an actual work piece,
switch on and let it run for a while. Operate
the tool at least 200 mm away from your face
and body.
▪ Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
6
EN
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
Even when the tool is used as prescribed it is
not possible to eliminate all residual risk factors.
The following hazards may arise in connection
with the tool's construction and design:
▪ Damage to hearing if effective hearing protec-
tion is not worn.
▪ Always unplug the machine prior to any ad-
justment, servicing or maintenance including
replacing the accessories.
▪ The power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Nut
2. Collet
3. Spindle
4. ON/OFF switch
5. Cord with plug
6 Electronic regulator of speed
7. Bush
8. Operating tool
9. Auxiliary handle

Operation

This power tool is supplied from single-phase al-
ternating current mains only. It is double insulat-
ed according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
This power tool is designed for minor finish
processing metal, plastics or wooden parts by
burnishing accessories after welding, grinding,
removing rust, structuring wood, etc.
Design features extended spindle for operation
in confined areas.
MKL 755CE