Essentiel EPGZ 1 Instrucciones De Uso página 18

Connecting the hose and regulator (not supplied)
This appliance is designed to be used in accordance with the information given in the tables below:
Country of destination
FRANCE, BELGIUM,
LUXEMBOURG
Rated power (∑Qn)
Mark on injector
•
The G1/2 gas inlet is located on the left side of the appliance.
•
Use a hose that complies with the national regulations in force (NF for France, BSEN 16129:2013
for other countries) of 37 mbar for Propane or 28-30 mbar for Butane with G1/2 threaded nut for
screwing into the appliance, and M20×1.5 threaded nut on the regulator, complying with NF D 36-
125 or XP D 36-112.
•
Comment: for other countries, cylinders and regulators must comply with applicable national regulations.)
•
The connection to the appliance must be made using a 1.2 m or 1.5 m long supply hose (maximum).
•
Change the main supply hose before its expiry date, if it is damaged, if it shows cracks, or when
national legislation requires it.
•
Do not pull or twist the hose.
•
Make sure that the hose is not subjected to torsional or tensile stress: the gas inlet connector is
located on the left side and the gas cylinder is positioned on the left side of the appliance.
•
Make sure that the hose is never in contact with parts of the appliance that may become hot.
!
Warning! Never connect your appliance to town gas (natural gas). The gas circuit is
designed exclusively for butane/propane gas (G30/G31).
ux
Fig. 1
Fig. 1: Tightening by hand is sufficient. Do not overtighten
To regulator
Vers détendeur
34
ur
V.1.0
25
connecting to the gas cylinder
1.
Utilisez un tuyau comportant un marquage NF et écrou fileté G1/2 pour le vissage sur l'appareil, et
écrou fileté 20×1.5 sur le détendeur, conforme à la norme XP D 36-125 ou à la norme XP D 36-112.
ou
2.
Vérifiez que toutes les manettes de commande de la plancha sont sur la position «
Category Gas and pressure
G30 - Butane: 28-30 mbar
I (28-30/37 mbar)
3+
G31 - Propane: 37 mbar
7.05kW (513.2g/h on Butane – 504.1g/h on Propane)
0.75
(Non-contractual diagrams)
Fig. 3
Fig. 2
(Schémas non contractuels)
To griddle
CONNECTOR:
FOR FRANCE
Use the G1/2 gas inlet located on the left side or rear side of the barbecue.
FOR OTHER COUNTRIES
Use the ringed connector supplied as a spare part.
Firmly screw the ringed connector onto the G1/2 gas inlet threaded connector using a suitable
tightening tool (wrench) and carry out the leak test (see next paragraph).
SUPPLY HOSE: FOR ALL COUNTRIES
Change the main supply hose before its expiry date, if it is damaged, if it shows cracks, or when
national legislation requires it. The hose must comply with EN16436-1:2014.
Do not pull or twist the hose.
Make sure that the hose is not subjected to torsional or tensile stress: the gas inlet connector is located
on the left side and the gas cylinder is positioned on the left side of the appliance.
Make sure that the hose is never in contact with parts of the appliance that may become hot.
Place the gas cylinder at least 1 metre away from the barbecue.
The connection to the appliance must be made using a 1.2 m or 1.5 m long supply hose (maximum).
Leak test
!
Warning!
•
This test must be carried out in a well-ventilated area before using the griddle, every
year, after a long period of disuse, or when replacing the gas cylinder.
•
Do not check for gas leaks near an open flame. If you smell gas, immediately turn off
the gas supply.
1.
Make sure that all of the control knobs are in the closed position "
2.
Prepare a soap and water solution (1/2 water and 1/2 soap) and run the solution through the gas
connection points of the cylinder, regulator, hose and gas connection using a brush.
3.
Open the gas cylinder valve.
Vers plancha
•
» (arrêt).
Soap
•
" (stop).
connecting to the gas cylinder
35
V.1.0