HIKOKI CR 36DA Instrucciones De Manejo página 13

4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Switch operation
Adjusting operating speed
Adjusting stroke
Mounting the blade
Dismounting the blade
*2
When the blade is broken
Adjusting the base
How to use the hook *4
Figure Page
2
3
4
5
*1
6
7
8
*3 9
10
11
How to use the LED light*
Remaining battery indicator
Select a saw blade of the
appropriate length
Fasten a workpiece fi rmly
Plunge cutting (for wood)
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 Adjusting operating speed
CAUTION
Select mode while the trigger switch is released. Failure
to do so could result in malfunction.
Once you install the battery and switch on the power, you
can change modes with each press of the mode selector
switch.
● Speed change mode allows the number of maximum
strokes to be switched between 4 levels: low speed,
medium speed, high speed and Max. speed.
With speed change mode, the set number of maximum
strokes will be maintained even if there is a change in
load.
Operating speed
Mode
Transmisson
Mode
*2 Dismounting the blade
CAUTION
Never touch the saw blade immediately after use. The
metal is hot and can easily burn your skin.
(1) After pivoting the lever, point the blade downward. The
blade should fall out on its own. If the blade fails to fall
out, pull it out by hand.
*3 When the blade is broken
Even when the saw blade is broken and remains inside
the small slit of the blade holder, it should fall out when
the lever is pivoted and the blade is pointed downward.
If the blade fails to fall out on its own, take it out by using
the procedures described below.
2
(1) If a part of the broken saw blade is sticking out of the
2
small slit of the blade holder, pull out the protruding part
and take the blade out.
3
(2) If the broken saw blade is hidden inside the small slit,
3
hook the broken blade using a tip of another saw blade
and take it out.
3
4 *4 How to use the Hook
The hook can be used to hang up the unit
4
temporarilyduring operations.
CAUTION
4
The hook should never be used to hang the unit on your
4
person.
5
13
12
5
13
14
15
16
17-a
17-b
18
19
―
Status Operating speed
Low 0 – 1700 min -1
Medium 0 – 2000 min
-1
High 0 – 2500 min
-1
Max. 0 – 3000 min
-1
English
5
5
5
5
6
6
6
6
6
275