Makita 5007MG Manual De Instrucciones página 64

Ocultar thumbs Ver también para 5007MG:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Playing audio files in Bluetooth
mode
When you have successfully connected the speaker with
the chosen Bluetooth device you can start to play your
music using the controls on your connected Bluetooth
device.
1.
Once playing has started adjust the volume to the
required setting using the Volume buttons
the speaker or on your enabled Bluetooth device.
When you press the Volume up/down button,
the volume indicator will flash in fast flashing red. If
the indicator light in solid red, it indicates the volume is
in maximum volume or minimum volume.
2.
Use the controls on your device to play/pause and
navigate tracks. Alternatively, control the playback
using Play/Pause (
track buttons (
) on the speaker.
3.
Press and hold the Next track
to fast-forward/Rewind the current track. Release
the button when the desired point in the track is reached.
Note:
1.
That not all player applications or devices may
respond to all of these controls.
2.
Some mobile phones may temporarily disconnect from
the speaker when you make or receive calls. Some
devices may temporarily mute their Bluetooth audio
streaming when they receive text messages, emails or
for other reasons unrelated to audio streaming.Such
behaviour is a function of the connected device and
does not indicate a fault with the speaker.
Speaker memory and reconnecting
a device
The speaker can memorize up to 8 sets of paired device,
when the memory exceed this amount, the oldest pairing
history will be over written. If your Bluetooth device
already paired with the speaker previously, the unit
will memorize your Bluetooth device and it attempts
to reconnect with a device in memory which is last
connected. If the last connected device is not available,
the speaker will be discoverable.
Disconnecting your Bluetooth
device
Press and hold the Bluetooth pairing button
seconds to disconnect with your Bluetooth device. The
Bluetooth indicator flashes in blue indicating the speaker
is discoverable again for pairing.
Playing music via auxiliary input
socket
A 3.5mm Auxiliary input socket is provided on the right
side of the unit to permit an audio signal to be fed into the
unit from any devices that features a headphone or audio
output, such as an iPod, MP3 or CD player.
1.
Connect a stereo or mono audio source (for example,
iPod, MP3 or CD player) to the Auxiliary input socket
(marked 'AUX') and the Aux in indicator turns green
indicating the speaker is in auxiliary input mode.
2.
Adjust the Volume control on your iPod, MP3 or CD
), Next track (
) , Previous
or Previous button
player to ensure an adequate signal and then adjust
the volume on the speaker for comfortable listening.
Note:
When Aux in socket is connected an audio device,
Bluetooth function will be disabled to minimize power
consumption.
MAINTENANCE
MAINTENANCE
on
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Specification
Amplifier
Output power
Frequency response
Aux In
Input sensitivity
Speaker
Main speaker
Tweeter speaker
Bluetooth
Bluetooth version
Bluetooth profiles
Transmission power
Transmission range
Supported codec
Compatible Bluetooth profile A2DP
General
AC power adaptor
Battery
Weight
for 2-3
The company reserves the right to amend the specification
without notice.
10.8V:3.5W
14.4V:6W
18V:10W
50Hz~20kHz
250mVrms @100Hz
101.6mm 8 ohm 10W
36mm 8ohm 10W
4.0
A2DP/ SCMS-T/ AVRCP
Bluetooth specification
power Class 2
Max. 10m (varies according
to usage conditions)
SBC
DC in 12V 1.5A, center pin
positive
Slide battery: 10.8V-12Vmax /
14.4 V/ 18 V
2.7KG (without battery)
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

5007mga

Tabla de contenido