Technical Specification; Double Insulation; Charging Battery Pack Instructions - Narex ASP 14-2A Instrucciones De Uso Originales

Technical specification

Cordless hammer drill/driver:
Model
Voltage
Idle speed:
Max. number of impacts:
Max. torque
Chuck – scope of clamping
Wood screws - dia. max.:
Drilling - dia. max.:
Threaded spindle for chuck
Weight w/o accumulators
Charger:
Model
Input voltage
Frequency
Power input
Output voltage
Charging current
Charge time
Weight
Class of protection
Accumulator:
Model
Voltage
Cell type
Capacity
Temperature of charging
Charge time
Monitor. of the temp.of charging
Weight
* Depending on model and capacity of the accumulator to be charged!
Description:
1 ...........Accumulator
2 ...........Accumulator clamp
3 ...........Switching–in push button with speed control
4 ...........Reversing switch
5 ...........Speed changing switch
6a .........Adjusting ring for torque setting
6b .........Adjusting ring for drilling/hammer-drilling
7 ...........Workplace LED lighting
8 ...........Chuck clamp sleeve
9 ...........Accumulator state indication panel
10a .......Indication switch
10b ......Accumulator state indicator
11 .........LED signal lights
12 .........Charger
13 .........Vent holes of the accumulator air cooling system
Zobrazené anebo popsané příslušenství nemusí patřit do objemu
dodávky.
ASP 14-2A
14.4 V
1st range 0–460 rpm
2nd range 0–1 600 rpm
1st range 0–6 900 ipm
2nd range 0–24 000 ipm
54 Nm
0.8–10 mm
7 mm
into metal 10 mm
into wood 35 mm
into masonry 10 mm
1/2"-20 UNF
1.36 kg
AN-UNI C
110–240 V
50–60 Hz
80–100 W
16.6–20.7 V
4 A
ca 25–45 min*
0.7 kg
II /
AP 14 LE AP 14 LP
14.4 V 14.4 V
Li-Ion Li-Ion
1.5 Ah 3.0 Ah
0–45 °C 0–45 °C
ca 25 min ca 45 min
thermistor thermistor
0.44 kg 0.68 kg
Scope of use
The cordless hammer drill/drivers are specified for screwing and
drilling into metals, wood and plastics and for hammer-drilling
into masonry.

Double insulation

To ensure maximum safety of the user our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 55014.

Charging battery pack instructions

1. Make sure that circuit voltage is the same as than shown on
the charger specification plate. Connect the charger (12) to
power source. Red LED signal light should light up (11). This
indicates the charger is ready to being charging. If the red LID
light is not on, check connection to the power source. If the
power source is OK, transport the charger into the authorized
service workshop!
2. Position the accumulator/battery pack (1) into the charger as
far as the stop, see the Fig.
ASP 18-2A
18.0 V
0–460 rpm
0–1 600 rpm
0–6 900 ipm
0–24 000 ipm
60 Nm
1.5–13 mm
8 mm
13 mm
40 mm
13 mm
1/2"-20 UNF
1.48 kg
AP 18 LE AP 18 LP
18.0 V 18.0 V
Li-Ion Li-Ion
1.5 Ah 3.0 Ah
0–45 °C 0–45 °C
ca 25 min ca 45 min
thermistor thermistor
0.52 kg 0.78 kg
English
17