REDWALL V serie Instrucciones De Instalación página 4

Mounting tips>>
• Engage the convex section of the area viewfinder fixing
arms with the notches of the main unit, and insert and
mount the arms.
Alarm Creep
• Mount the area plate so that an arrow of the plate
center section faces upward and the letter surface can
be seen.
• Insert the area plate into the top and bottom grooves of
the area viewfinder until the plate is stopped by the ribs.
SIP-5030
Arrow
marking
3 4
5030
2 5
1
7 8 9
B1
B3 B4
B2
C1 C2 C3 C4 C5 C6
D1 D2 D5 D6
D3 D4
E1
E2 E3 E4 E5
F1
F2 F3 F4 F5
(5)
Fine adjust the main unit angle in vertical and horizontal
direction by observing the target area through the area
viewfinder.
1
2
Move your face close to the viewfinder
so that your eye comes within 5 mm of
the inspection window (lens surface).
3
Locate the center circle of the area
plate on the center circle of the lens
of the area viewfinder, and check the
detection area pattern on the area
plate and the background image.
* Each letter on the area plate
corresponds to each mirror number
(see Step 8-2).
* You cannot observe mirror
numbers B to F and B6 to F6
(shown at right) of the SIP-5030
area plate through the inspection
window. Check them using the
walk tester.
Adjusting tips>>
If you experience any of the following, see Step 0.
5030 3 4 (521206)
2 5
1 6
9
7 8 10
B6
B1
B2 B3 B4
C1 C2 C3 C4 C5 C6
D1 D2 D5 D6
D3 D4
E1 E6
E2 E3 E4 E5
F1 F6
F2 F3 F4 F5
The sensor area is extended
over the street where a person
walks or a car drives.
Fixing arms
Notch
Convex
section
SIP-00
Grooves
100 (521207)
1
2
(521206)
6
B1 B2
10
C1 C2
B6
D1D2
E1 E2
E6
F1 F2
F6
Ribs
To change the direction of the inspection
window, rotate the area viewfinder in a
horizontal direction until it clicks and stops.
Center circle of the lens
Center circle of the
area plate
3 4
5030
2 5
1 6
7 8 9 10
B1 1 1 1
B2 B3 B4
C1 C2 C3 C4 4 C5 C6
D1 1 D2 D5 D6 6
D3 3 D4 4
E E E1
E2 E3 E4 E5
F1 F6
F2 F3 F4 F5
The detection area is
inside the frame
Invisible area
border.
5030 3 4 (521206)
2 5
1 6
9
7 8 10
B6
B1
B2 B3 B4
C1 C2 C3 C4 C5 C6
D1 D2 D5 D6
D3 D4
E1 E6
E2 E3 E4 E5
F1 F6
F2 F3 F4 F5
Branches of a tree and grass
move when the wind blows.
Cautions>>
• The area viewfinder is a supporting tool for detection
area adjustment.
• After you have adjusted the detection area using the
area viewfinder, always check the area using the walk
tester.
• Never look directly into the sun through the area
view finder.
• After you have used the area viewfinder, store it away
from direct sunlight.
(6)
Securely tighten the adjustment screw that you have
loosened.
(7)
Connect the walk tester (optional) to the sensor unit, and
check that the detection area is correct.
When the power selector switch is turned to "POWER
1
SUPPLY FROM SENSOR" position after plugging
the cable into the walk tester connector, a continuous
beeping sound will be heard.
When a pedestrian first enters the detection area, the
2
strong and weak beeps will sound alternately.
When the entirety of a pedestrian's body is detected, the
3
strong beep will sound continuously.
(521206)
B6 B B B
E6 6 6
- 4 -
For creep zone alarm output
For near area alarm output
For far area alarm output
Use at "REDWAVE ALARM
OUTPUT" position to
confirm far and near area
alarm output.
Use at "REDWALL" position. Power selector
switch
REDWAVE REDWAVE
PIR NEAR PIR FAR
REDWAVE
MICROWAVE
REDWAVE
REDWALL
REDWIDE
MEGARED
REDWALL MEGARED
REDWIDE
FAR
MEGARED
NEAR
CONNECTION MODE
SELECT SELECT
SWITCH SWITCH
OPM-WT
WALKTESTER
REDWAVE
ALARM OUTPUT
CELL BATTERY
POWER
SUPPLY
FROM
SENSOR
POWER OFF
POWER
SELECT
SWITCH