Guarantee; Liability Exclusion; Conformity Declaration - Multiplex Power Peak D7 EQ-BID Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 62
[ Error ]
BID interruption!
* The BID system was con-
nected while a process was
active.
[ Error ]
BID error
* The BID system has been
connected or
disconnected.

20. GUaraNtEE

Naturally all our products are guaranteed for 24 months as requi-
red by law. If you wish to make a justified claim under guarantee,
please contact your dealer in the first instance, as he is respon-
sible for the guarantee and for processing guarantee claims.
During the guarantee period we will rectify any functional defects,
production faults or material flaws at no cost to you. We will not
accept any further claims, e.g. for consequential damage.
Goods must be sent to us carriage-paid; we will pay return carri-
age costs. We will not accept any packages sent without pre-paid
postage.
We accept no liability for transport damage, nor for the loss of your
shipment. We recommend that you take out appropriate insurance.
Send your device to the approved Service Centre in your country.
the following requirements must be fulfilled before we can
process your guarantee claim:
• You must include proof of purchase (till receipt) with the retur-
ned product.
• You must have operated the product in accordance with the
operating instructions.
• You must have used recommended power sources and genui-
ne robbe accessories exclusively.
• There must be no damage present caused by moisture, unau-
thorised intervention, reversed polarity, overloading or mecha-
nical stress.
• Please include a concise, accurate description of the fault to
help us locate the problem.
MULTIPLEX Modellsport GmbH & Co.KG
Westliche Gewerbestr. 1
D-75015 Bretten (Gölshausen)
phone: 0049 7252 580 93 0
Operating Instructions
Power Peak
[ Error ]
BID incompatible
* Invalid data on the BID
chip or key.
(possibly LiPo cell count
greater than seven cells)
[ Error ]
Internal temperature
* The internal temperature is
excessive. Allow the charger to
cool down.
D7 EQ-BID
®

21. LIaBILIty ExCLUSION

This battery charger is designed and approved solely for the
purpose of charging the batteries defined in the operating
instructions. MULTIPLEX Modellsport accepts no liability
whatsoever if the charger has been used for any purpose other
than the intended one.
MULTIPLEX Modellsport is unable to ensure that you observe the
assembly and operating instructions, or the conditions and methods
employed for installing, operating and maintaining the radio control
system components.For this reason we accept no liability for loss,
damage or costs which are due to the erroneous use and operation
of our products, or are connected with such operation in any
way.Regardless of the legal argument employed, our obligation to
pay compensation is limited to the invoice value of those
MULTIPLEX products directly involved in the event in which the
damage occurred, unless otherwise prescribed by law. This does
not apply if the company is deemed to have unlimited liability
according to statu-tory regulation due to deliberate or gross
negligence.
22. DISPOSaL Of USED EQUIPMENt
Electronic equipment must not simply be discarded
in the normal domestic waste. That is the meaning
of the symbol shown here, which you will find on
the Power Peak® D7 EQ-BID. This symbol means
that you should dispose of electrical and electronic
equipment separately from the household waste at
the end of its useful life. Please take your unwanted
device to your local communal collection point of recycling centre.
This requirement applies to member countries of the European
Union as well as other European countries with a separate waste
collection system.

23. CONfOrMIty DECLaratION

robbe Modellsport GmbH & Co. kG hereby declares that this
device conforms to the fundamental requirements and other rele-
vant regulations of the corresponding EC Directives. You can
read the original Conformity Declaration on the Internet at www.
robbe.com: click on the "Conformity Declaration" logo button which
you will find next to the corresponding device description.
Errors and technical modifications reserved.
Copyright robbe-Modellsport 2014
Duplication and copying of the text, in whole or in
part, is only permitted with the prior
written approval of robbe-Modellsport GmbH & Co.
KG
15
Order No.
8129

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

30 8129

Tabla de contenido