Always Do The Following To Maintain Washer Freshness; Cleaning The Exterior; Cleaning The Dispenser Drawer - Whirlpool duet steam WFW9600TZ00 Manual De Instrucciones

Lavadora automatica de carga frontal
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

6=
The cycle will determine whether clothing or other items are
in the washer.
a} If no items are detected in the washer, it will proceed to
Step 7.
b} If any items are detected in the washer, "rL" will be
displayed, and the WASH and CONTROLS LOCKED
lights will remain lit. The door will unlock. Open and
remove any garments in the wash drum.
Press PAUSE/CANCEL to cancel the failure code.
Then repeat steps 3, 4 and 5 to start the cycle again.
7. Once the cycle has begun, allow the cycle to complete.
8. After the cycle is complete, leave the door open slightly, to
allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness
Use only HE High Efficiency detergent.
Leave the door slightly open after each cycle to allow for
better ventilation and drying of washer interior.
Repeat the cleaning procedure monthly or when the CLEAN
WASHER REMINDER light illuminates.
If you are not ready to run the Clean Washer cycle, but the
Clean Washer Reminder light is illuminated,
press the Clean
Washer Reset button.
If the procedure does not sufficiently improve the machine
freshness, evaluate your installation and usage conditions for
other causes.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever in
the oxygen based stain fighter/color-safe
bleach
compartment.
See "Using the Dispenser." Remove the
drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments
and the detergent selector).
3. Wash the parts under running water.
4. Replace the inserts and return the dispenser to the drawer.
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.
_* I I
:I_'10'
1_1(itt,;_t1I/
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use
or vacation
care:
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
Unplug washer or disconnect
power.
Turn off the water supply to the washer. This helps avoid
unintended flooding (due to a water pressure surge) while you
are away.
Slightly open door to provide ventilation.
To winterize washer:
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.
2. Run washer on a Drain/Spin cycle.
3. Unplug washer or disconnect
power.
4. Shut off both water faucets.
5. Disconnect
water inlet hoses from faucets and drain.
To use washer
again:
1. Flush water pipes. Reconnect water inlet hoses to faucets.
Turn on both water faucets.
Electrical
Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow
these instructions can result in death,
fire, or electrical
shock.
2. Plug in washer or reconnect power.
3. Run the washer through the Quick Wash cycle with 1/2the
manufacturer's
recommended
amount of HE detergent for a
medium-size
load, to clean the washer and remove the
antifreeze, if used.
To transport the washer:
1. If washer will be moved during freezing weather, put in
1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a
Drain/Spin cycle.
2. Unplug the power cord.
3. Disconnect the drain hose from the drain system and attach
to rear panel clips.
4. Shut off both water faucets.
5. Disconnect the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
IMPORTANT: Call for service. Do not reuse transport
bolts.
Washer must be transported
in the upright position. To avoid
suspension and structural damage to your washer, it must be
properly set up for relocation by a certified technician.
Reinstalling
the washer
1. Follow the "Installation
Instructions" to locate, level and
connect the washer.
2. Run the washer through the Quick Wash cycle with 1/2the
manufacturer's
recommended
amount of HE detergent for a
medium-size
load, to clean the washer and remove the
antifreeze, if used.
2O

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido