Airplay™ Setup; Battery Installation; Battery Replacement; Safety Cover Installation And Use - Airplay AIR-1-010011-H1 Manual Del Usuario

AIRPLAY™ Setup

Battery Installation

Battery Installation Battery Installation Battery Installation Battery Installation
Your new AIRPLAY™ controller has been equipped with reLOAD™, the most
revolutionary battery swapping technology ever created. reLOAD™ allows you to load
and/or replace the single AA battery (not included) used to power the AIRPLAY™
Controller, in less than a second. This means that you can keep playing until the
reLOAD™ "Low Battery Indicator" tells you that your battery is running low.
Before you can begin gaming with your new AIRPLAY™, you must install a battery. To
install a battery in your AIRPLAY™ Controller, do the following:
1. Rest a single AA battery on the top of the reLOAD™ battery bay making sure that the
positive (+) battery terminal is oriented to the left of the reLOAD™ bay. The correct
battery polarity is represented by the battery polarity icon directly above the
reLOAD™ Low Battery Indicator.
(NOTE: The reLOAD™ battery bay has been specially designed with the
battery's positive terminal channel on the left side. This design ensures that
battery installation is best accomplished with the battery set with the correct
polarity inside the reLOAD™ battery bay. If you attempt to load a battery into
the reLOAD™ battery bay and you find that you have to use excessive force to
seat the battery, STOP and check to see that the positive battery terminal is
oriented correct. To confirm correct polarity direction, refer to the battery
polarity icon located between the battery bay and the reLOAD™ Low Battery
Indicator.)
2. Grip the controller with both hands in playing
position. Apply even pressure on each end of
the battery using both thumbs until the battery
snaps into the fingers of the reLOAD™ battery
bay (refer to accompanying diagram).

Battery Replacement

Battery Replacement Battery Replacement
Battery Replacement Battery Replacement
Changing the battery in your AIRPLAY™ Controller
is just as easy as installing the first battery. To
replace the battery in your AIRPLAY™ Controller,
follow the steps outlined in the Battery Installation
section above. As the new battery moves into place
in the reLOAD™ battery bay, it will push the old
battery out the bottom of the reLOAD™ battery bay
(refer to accompanying diagram).
Push the new battery in from the top...
4
Combi-1.p65 4
... and the old battery drops out the bottom.
After changing the battery, simply continue playing. The reLOAD™ mechanism has
been designed to change the single AA battery in less than a second. This makes it
possible to change a battery "on the fly" without stopping your game.
CAUTION: CAUTION: CAUTION: CAUTION: CAUTION:
To allow proper battery changing, ensure the bottom of the reLOAD™
battery bay is not obstructed when replacing the battery. ALWAYS point the bottom of
the reLOAD™ battery bay to the ground when changing a battery in AIRPLAY™.

Safety Cover Installation and Use

Although not necessary for regular use and operation of your AIRPLAY™ Controller,
the Safety Cover may be used to cover the reLOAD™ battery bay should you have
small children in your house. AA BATTERIES ARE SMALL ENOUGH TO BE
SWALLOWED AND THEREFORE ARE A HAZARD TO SMALL CHILDREN (for more
information refer to the PRECAUTIONS section at the front of this manual).
To install the Safety Cover on your
AIRPLAY™ Controller follow these steps:
1. Hold the AIRPLAY™ Controller firmly in
one hand at the middle section of the
Controller housing.
2. Using your other hand, set the Safety Cover
over the bottom of the front housing of the
reLOAD™ battery bay. Because the Safety
Cover is made of a flexible plastic, you can
spread open the other end of the Safety
Cover as you push it into place at the top of
the reLOAD™ battery bay (refer to
accompanying diagram).
w w w . a i r p l a y e r . n e t
11/1/99, 1:11 PM