Tabla de contenido
Publicidad
OPERATING INSTRUCTIONS
Changing the Headlight Bulb
WARNING: To reduce the risk of
electric shock, the power cord
must be disconnected before removing
the dust cup, HEPA filter,changing the
filters or performing maintenance/trouble
shooting checks.
1.
Turn unit "Off" and unplug from
wall
outlet.
2.
With a flat head screw driver, snap
off the lens cover by pressing
down on the two notches on the lens
cover. (Fig. 29)
3.
Lift off the head light lens.
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
PROBLEM
POSSIBLE CAUSE
1.
Not properly plugged into
wall outlet.
Cleaner Won't
2.
No electricity in wall outlet.
Run
3.
On/Off switch not turned on.
4.
Motor thermostat tripped.
5.
Blown fuse/tripped breaker.
1.
Full or clogged dust cup.
2.
Wrong pile height setting.
3.
Clogged nozzle.
4.
Clogged dust inlet port.
5.
Clogged hose.
6.
Broken belt.
Cleaner Won't
7.
Hose not inserted fully.
Pick Up
8.
Dirty filters.
9.
HEPA filter needs cleaning
or replacing.
10. HEPA filter frame needs
cleaning.
11. Blockage in unit.
Cleaner Picks
Up Moveable
1.
Wrong pile height setting.
Rugs Or Pushes
Too Hard
Agitator Does
1.
Broken belt.
2.
Belt installed incorrectly.
Not Turn
1.
Attachment use restricts air
Air Flow
flow.
Restricted With
2.
New carpet debris clogging
Attachment Use
air path.
Notches
Fig. 29
4. Remove the light bulb by pulling it out
carefully.
5. Replace the new bulb by pushing it in.
6. Replace the head light lens by pushing
it in so that it snaps back in place.
POSSIBLE
1.
Plug in firmly.
2.
Check fuse or breaker.
3.
Push on/off switch to on
4.
Reset motor thermostat.
5.
Reset circuit breaker or replace fuse.
1.
Clean dust cup.
2.
Adjust setting.
3.
Remove obstruction.
4.
Remove power head cover and
remove obstruction.
5.
Remove obstruction.
6.
Replace belt.
7.
Push hose in securely.
8.
Clean / change filters.
9.
Clean or replace HEPA filter.
10. Clean HEPA filter frame.
11. Check unit for blockages.
1.
Adjust setting.
1.
Replace belt.
2.
Check belt changing and agitator
cleaning.
1.
Check attachment.
2.
Remove obstruction.
10
MESURES DE PRÉCAUTION
Important:
Si la trappe de succion ou le boyau se BLOQUENT, éteignez
l'aspirateur et retirez l'obstacle avant de redémarrer l'appareil.
1.
N'approchez pas l'aspirateur
trop près des éléments
chauffants ou des radiateurs.
2. Avant d'insérer la fiche d'alimentation
dans la prise murale, assurez-vous
que vos mains sont sèches.
3. N'aspirez aucun liquide.
4.
Tenez toutes les parties du corps,
les doigts, les cheveux et les
vêtements lâches éloignés des
ouvertures, du batteur rotatif et des
autres pièces mobiles.
5.
Lorsque vous retirez le cordon
d'alimentation de la prise
murale, tirez sur la fiche et non
pas sur le cordon.
6.
Ne ramassez aucun objet fumant
ou brûlant tels que les cigarettes,
allumettes ou cendres chaudes.
7.
Évitez de faire passer l'aspirateur
sur le cordon d'alimentation.
8.
N'utilisez pas l'aspirateur sans
sa coupelle ou sans ses filtres.
9.
Avant de commencer à nettoyer,
assurez-vous de retirer tout gros
objet ou tout objet coupant
pouvant endommager
l'aspirateur.
27
Publicidad
Tabla de contenido
