How To Pair The Btnext To A Gps; How To Use A Gps; How To Pair Pmr446 Transceiver With Integrated Bluetooth; How To Listen To The Fm Radio - Midland BTNext Manual De Instrucciones

Priority: the music listening mode has the lowest priority. Therefore, it will always
be disabled when another type of communication is enabled.

How to pair the BTNext to a GPS

In general is possible to pair the BTNext to all the GPS for motorbike that support
Bluetooth headset connection.
To pair the BTNext to a GPS, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is
on permanently.
3. Now press firmly (3 sec) the "Volume -" button, the Blue and Red light will
flash.
4. Enable the Bluetooth device search feature on your GPS
5. After some seconds, "Midland BT NEXT" will be displayed on your GPS.
6. Follow the pairing procedure of your GPS. If a pin code is requested you must
enter "0000" (four times zero).
7. When successfully paired, the Blue light of the unit will be on for one second
and then the unit will exit the setup mode and switch to the working mode
(the Blue light will start flashing).
You can now use your BTNext and the GPS street voice announcement are always
in background.
If you pair the GPS to the Volume + button (because for example the "Volume
–" button was already used), you loose the possibility to pair the phone to the
BTNext unit. You can overcome this limit by pairing the phone directly to the GPS
and then the GPS to the BTNext unit. All the phone features are therefore mana-
ged by the GPS itself.

How to use a GPS

When paired using the "Volume -" button the GPS will be automatically con-
nected and the voice announcement are always in background also if the inter-
com is active.
When the GPS is paired to the "Volume +" button, the street voice announce-
ment will always interrupt the intercom. In addition, remember to switch to
"Phone" mode in order to listen and control the music (play/pause - backward
and forward).
If the phone is connected thru the GPS you must use the control buttons on the
GPS screen in order to control the phone functionality.
C-Radio FM mode
Mode Forward button
FM Radio Short press: Scan recorded
Long press: seek station up

How to pair PMR446 transceiver with integrated Bluetooth

If your PMR446 trasceiver has an integrated Bluetooth (like the G8BT), you must
pair the trasceiver using the "Volume –" button:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is
on permanently.
› Now press firmly (3 sec) the "Volume -" button, the Blue and Red light will
flash.
› Follow now the pairing procedure explained on the manual of the transceiver
itself
Attention: If you are pairing to a G8BT transceiver, just when the BTNext finish the
pairing (only the Blu LED is flashing) you must follow this procedure to activate the
Bluetooth connection:
› Turn off and on the G8BT and then press for 3 sec. the "BT" button.
› Follow the same procedure every time you need to reconnect the G8BT to the
BTNext (no need to make the pairing procedure again)

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the
"FM Radio" mode in order to use it. Long press the middle button until you hear
"FM radio" from the voice announcement. Now all the three main button are de-
dicated to the FM Radio (See Table C).
Attention : To toggle wired on/off pressing long the Backward button, you need first
to stop the FM Radio (Press the Middle button briefly).
When you press the Forward or the Backward button briefly, you can scan up or
down the 6 recorded stations. A voice announcement will tell you the number of
which memory you are entering. A double beep tone will be played when the last
or the first recorded station is reached.
To save the station you are listening, press the Forward and Rear buttons together
for 3 sec. You will hear a beep tone for confirmation.
The station is saved over the last recorded station used.
Thanks to the RDS system, the FM Radio will choose the strongest signal available
for the radio station you like to listen.
The RDS system is OFF by default, if needed you can toggle on/off the RDS pres-
sing together the "Volume +" and "Volume –" buttons for 3 sec when the radio is
on. A voice announcement will tell you the RDS status.
Middle button
Short press: On/off
Long press: Change mode
Midland BT Next - 11
Rear button
Short press: Scan recorded
Long press: seek station down