CORBERO CCVV320 Manual De Usuario página 50

a status change of the Dual and Triple
zones in the following manner: dual zone
on/off, triple zone on, all extended zones
off, dual zone on/off, triple zone on, all
zones off, and so on.
Set Cooking Level with and without Heat
Boost
All heaters are equipped with the heat
boost function.
If the heat boost is required, set the heat
from the current level to level 9 by pressing
the button only. Once level 9 has been
reached, press
boost. The display will flash "A" alternating
with the heat setting value "9" to show the
heat boost is active.
If the heat boost is active, the heater will
operate with maximum power for a period of
time dependent on the heat setting selected
before the heat boost was activated.
Once the heat boost time has ended, only
the heat setting will be indicated on the
heater display.
The heat boost can be deactivated by
pressing until the heat setting "0" is
displayed.
Switching Off Individual Heaters
A heater can be turned off in 3 different
ways:
• Simultaneous pressing of
buttons
• Reduction of the heat setting to "0" by
pressing the
• Use of the timer switch-off function for
the corresponding heater.
Simultaneous operation of
buttons
The corresponding heater must be chosen
with the Activate/Deactivate Heater Button
, the Decimal Point of the related
Heater Display will then flash. To switch
off the heater, and
simultaneously. A buzzer will sound and "0"
will appear in the heat setting display when
this is successful.
If the timer is active for the selected heater,
then "0" will appear in the heater and timer
displays, and the related Cooking Zone
Indicator and the Timer Function will both
switch off.
If there is any residual heat for the heater,
this will be indicated by a "H" in the heat
setting display.
Reduction of the heat setting to "0" by
to activate the heat
and
button
and
must be pressed
operating
The heater can also be switched off by
reducing the heat setting to "0".This causes
the associated Decimal Point of the heater,
the related Cooking Zone Indicator and the
Timer Display to all switch off, also.
If there is any residual heat for the heater,
this will be indicated by a "H" in the heat
setting display.
Use of timer switch-off function for
corresponding heater (if available)
After counting down to zero, the timer will
stop. The corresponding heater will show
"0" in the Heater Display and the Timer
Display will show "00". The corresponding
Cooking Zone Indicator will disappear.
An assigned Dual/Triple Zone Selection
Indicator will also disappear if it is active.
Additionally, the buzzer will sound when the
timer stops. Pressing any button will silence
the timer.
Key Lock
The key lock function is used to set 'safe
mode' on the appliance and can only be
used in Operating Mode (B-Mode). The lock
function becomes active when the key Lock
button is pressed for at least 2 seconds.
This operation is acknowledged by a buzzer
and the Key Lock Indicator will flash to
indicate the heater is locked.
If the heater is locked, it will only be
possible to switch the appliance off by
pressing
and it will not be possible to make any
adjustments by pressing the buttons. If any
other button is pressed in the lock mode,
the buzzer will sound and the Key Lock
Indicator will flash.
Only the switch-off operation by pressing
is possible. However, if the appliance is
switched off, it can not be restarted again
without being unlocked.
Child Lock
The child lock function is used to lock
the appliance in a complicated multi-step
process. Child lock (and unlocking) is only
available in the S-Mode.
First, must be pressed until the buzzer
sounds, then
simultaneously for at least 0.5 seconds,
but no longer than 1 second. Following
this, press
All four heater displays will show "L" as
confirmation.
EN - 14
button
, all other buttons are blocked
and must be pressed
to activate the child lock.