Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
WORK AREA
1.
Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.
Protect others in the work area from debris such as chips and sparks.
Provide barriers or shields as needed.
ELECTRICAL SAFETY
4.
Grounded tools must be plugged into an outlet properly
installed and grounded in accordance with all codes and
ordinances. Never remove the grounding prong or modify the
plug in any way. Do not use any adaptor plugs. Check with a
qualified electrician if you are in doubt as to whether the outlet
is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry elec-
tricity away from the user.
5.
Double Insulated tools are equipped with a polarized plug (one
blade is wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electri-
cian to install a polarized outlet. Do not change the plug in any
way. Double insulation
grounded power cord and grounded power supply system.
6.
Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
7.
Do not expose power tools to rain or wet conditions. Water en-
tering a power tool will increase the risk of electric shock.
8.
Do not abuse the cord. Never use the cord to carry the tools or
pull the plug from an outlet. Keep cord away from heat, oil, sharp
edges
or
moving
immediately. Damaged cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor
extension cord marked "W-A" or "W". These cords are rated for
outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
10. Stay alert, watch what you are doing, and use common sense
when operating a power tool. Do not use tool while tired or un-
der the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools may result in seri-
ous personal injury.
11. Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long hair can be caught in
moving parts.
page 2
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
eliminates the need for the three wire
parts.
Replace
damaged
WARNING!
12. Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch or
plugging in tools with the switch on invites accidents.
13. Remove adjusting keys or wrenches before turning the tool on.
A wrench or a key that is left attached to a rotating part of the tool
may result in personal injury.
14. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in unex-
pected situations.
15. Use safety equipment. Always wear eye protection. Dust mask,
non-skid safety shoes, hard hat, or hearing protection must be used
for appropriate conditions.
16. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control.
17. Do not force tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is
designed.
18. Do not use tool if switch does not turn it on or off. Any tool that
cannot be controlled with the switch is dangerous and must be re-
paired.
19. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool
accidentally.
20. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
21. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools with sharp cutting edge are less likely to
bind and are easier to control. Do not use a damaged tool. Tag
damaged tools "Do not use" until repaired.
22. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool's opera-
cords
tion. If damaged, have the tool serviced before using. Many acci-
dents are caused by poorly maintained tools.
23. Use only accessories that are recommended by the manufac-
turer for your model. Accessories that may be suitable for one tool,
may become hazardous when used on another tool.
24. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified per-
sonnel could result in a risk of injury.
25. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of this manual.
Use of unauthorized parts or failure to follow Maintenance Instruc-
tions may create a risk of electric shock or injury.
TOOL USE AND CARE
SERVICE
Publicidad
Tabla de contenido
