JB Systems LED DIRECTOR Manual De Instrucciones página 4

ENGLISH
FUNCTIONS
(FRONT)
1. POWER SWITCH: used to switch the unit on/off.
2. FIXTURE BUTTON: used to select/deselect a projector, the RGB-indicator indicates the status:
 RGB-indicator ON: output is on and ready to be edited (press fixture button shortly)
 RGB-indicator BLINKS: output is on but not editable (press fixture button shortly)
 RGB-indicator OFF: output is off and not editable (press fixture button for about 1 second)
3. BLACKOUT / AUTONOME BUTTON: this button has two different functions:
 BLACKOUT: press the button shortly to turn blackout on/off, the yellow LED is lit while the outputs
are set to zero.
 AUTONOME: press the button for about 1second to shut the DMX-signal off on all DMX-output 
the connected projectors start working in automatic standalone mode. The yellow LED blinks, while
the LCD-display shows "STAND ALONE". Press the button shortly to switch this mode off.
4. MENU / FADE TIME BUTTON: this button has two different functions:
 MENU: press the button for about 1 second to access the setup menu: see further for more
information on the setup menu. Press the button shortly to leave the setup menu.
 FADE TIME: The fade time determines how long it takes to fade from one color to another. Press
this button to edit the fade time. Can be used in chase playback mode or when a macro is edited.
Just use the dial (14) to change the fade time from 0 seconds up to 90 minutes.
5. CHASE BUTTON: used to select one of the 24 chases, just turn the dial (14) to choose the chase.
6. SCENE BUTTON: used to select a scene inside a chase (the display shows "MANUAL") , just turn the
dial (14) to choose the desired scene.
7. COLOR BUTTON: press this button (the display shows "Color") to set the desired color now select 1 or
more fixtures (2) and use the dial (14) to choose one of the 255 available colors.
8. FADE BUTTON: The fade time determines how long it takes to fade from one color to another. Press
this button (the display shows "Fade") and use the dial (14) to set the desired fade time of the selected
fixture(s).
9. MACRO BUTTON: there are 24 pre-programmed macros that you can use to make scenes and chases.
Press this button (the display shows "Macro") and use the dial (14) to choose the desired macro for the
selected fixture(s). You can adapt the Fade time (4) and wait time (13) as you like.
10. DIMMER BUTTON: this button has two different functions:
 IN PROGRAM MODE: you can press this button and use the dial (14) to set the dimming level of one
or more selected fixture(s).
 IN PLAYBACK MODE: you can press this button and use the dial (14) to set the dimming level of all
outputs. (master dimmer)
11. PROGRAM / RECORD BUTTON: this button has two different functions:
 PROGRAM: press the button for about 1 second to access the chase program mode (green LED
blinks) and use the dial (14) to choose the chase you want to create or edit. When editing is done,
press the button again for about 1 second to leave the program mode.
 RECORD: while in program mode, press this button shortly to saved the scene you just edited. The
display shows "STORE OK" and jumps to the next step.
12. DISPLAY: makes using and programming a lot easier. When a DMX-signal is detected on the DMX-
input (18), the display shows the start address you selected for the incoming DMX-channels.
13. ENTER / WAIT TIME BUTTON: this button has two different functions:
 ENTER: press the button shortly to confirm the menu settings shown on the display.
 WAIT TIME: The wait time determines how long it takes before the next scene starts or the next step
in a macro is done. Press this button to edit the wait time. Can be used in chase playback mode or
JB SYSTEMS
®
OPERATION MANUAL
3/50 LED DIRECTOR
ENGLISH
when a macro is edited. Use the dial (14) to change the wait time from 0 seconds up to 90 minutes.
14. DIAL KNOB: used to browse menus and change different values shown on the display.
FUNCTIONS
(REAR)
15. FIXTURE OUTPUTS: used to connect the LED projectors in a "star-configuration". All 6 outputs use 4
channels, each with the same order: R+G+B+DIM (or DIM+R+G+B ~ see setup menu)
16. DMX OUT: used to connect all LED projectors in a "daisy chain configuration" (all units in one DMX line).
The channels of the different projectors are merged to 24 channels:
 Fixture1 = channels 001 to 004
 Fixture2 = channels 005 to 008
 Fixture3 = channels 009 to 012
 Fixture4 = channels 013 to 016
 Fixture5 = channels 017 to 020
 Fixture6 = channels 021 to 024
17. DMX IN: normally not used BUT you can connect an external DMX-controller. As soon as a DMX-signal
is detected on this input, this DMX-signal takes precedence of the outputs generated by the LED
Director. This means that an external DMX-controller can automatically take over the control over the
fixtures connected to the DMX-outputs. You can even determine starting from which address the
incoming DMX-channels should be routed to the outputs (see item 5 in the chapter "setup menu").
18. DMX THROUGH: This is an exact copy of the DMX input (17) and is used to daisy chain the LED
Director in a big installation.
19. DC-INPUT: input for power adapter. The input supports 9V
CONNECTIONS
The LED fixtures can be connected to the LED Director in two ways:
STAR CONFIGURATION
The 6 DMX-outputs (15) are used and the
connected LED fixtures all have start address
001. Of course you can put several LED fixtures
(ex. 1A and 1B on the drawing) on one output
but all should have the same start address 001.
DAISY CHAIN CONFIGURATION
All LED fixtures are connected to DMX-out (16).
All LED fixtures receive their own start address,
(see n°16 in the previous chapter) depending on
which of the 6 channels you want to assign them
to.
JB SYSTEMS
®
OPERATION MANUAL
to 12V @ minimum 300mA.
dc dc
4/50 LED DIRECTOR