Royal Catering RCKT 180/70 Manual De Instrucciones página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
GENERAL HINTS FOR THE USER
Cooling table can be filled or upgraded when the table has reached the desired
set temperature. Never insert to the cooling table hot food and liquids as well
as food products without cover. Food products and drinks should be stored in
sealed airtight containers. When you first filling of the table, open it and fill only
one shelf in order to avoid tipping over the table. At the time of setting items in
the table is advisable to leave space between the product and the walls inside the
device, this will allow for adequate air circulation. If the door is opened too often,
there is increased energy consumption, which could lead to possible damage.
5. KEEP THE DEVICE CLEAN
Before cleaning or performing maintenance work, the machine must be disconnected
from the power and wait until it cools down. For cleaning, do not use harsh deter-
gents and make sure that the device does not enter the water. Never immerse the
appliance, cord or plug in water or any other liquid. It is forbidden to clean the device
with a water jet. It is recommended to wash the cooling table regularly. The interior
of the device should be cleaned with a disinfectant suitable for the food industry. To
clean, use a damp, soft cloth and then dry thoroughly. Do not use abrasive cleaners,
such as scouring powder, containing alcohol, thinners, etc. Dry the surface with a soft,
dry cloth. The following actions should be taken if the machine is not used for a long
period of time: Unplug the appliance, remove from the table all foods, wash table in-
side and outside with a damp, soft cloth and a mild detergent, rinse with clean water
and allow to dry, for some time to leave the door open so that the device thoroughly
dried. From time to time, check that the cable is not damaged. Do not use the ap-
pliance if the cable is damaged. A damaged cable must be replaced by a service or a
qualified electrician. In the event of damage or malfunction, please contact your dealer
or our service. Please pay attention to the troubleshooting tips described in the sec-
tion „Troubleshooting". Maintenance and repair work must be done only by qualified
personnel using original spare parts and accessories. Attempts to make repairs on
your own can lead to a direct threat to life or health, and will void the warranty!
6. DESCRIPTION OF THE COOLING TABLE RCKT-180/70 (ART. 1178)
18
1 – Work table made of stainless
steel
2 – Drawers
3 – Door
4 – Vents
5 – Digital thermostat
6 – ON/OFF switch
Rev. 19.05.2017
7. DIGITAL THERMOSTAT
Button
Normal operation
Single pressing button
UP
Single button pressing –
ON/
setting the parameters
OFF
„upward".
(turning
Pressing for more than
on /
3 seconds – switching
turning
between ON/OFF (ON –
off)
device in normal opera-
tion, OFF – device is tur-
ned off, the temperature
regulation and defrosting
are turned off.
DOWN
Single button pressing –
Defrost
setting the parameters
„downward".
Pressing for more than 3
seconds – turning on and
off the defrosting mode.
SET
Button pressed for 1 se-
MUTE
cond: setting the desired
set point.
Button pressed for more
than 3 seconds: entering
the setup menu.
Turning off the alarm
(mute).
NOTE! If any change in the setup menu is needed, please contact your service agent
or qualified Technician.
Rev. 19.05.2017
Start up
Pressing
together
buttons
Buttons
pressed
together:
activating
/ deac-
tivating
conti-
nuous
cycle
Pressing
Button
buttons
pressed for 1
to-
second: dis-
gether:
play showing
– start
the firmware
of the
version code.
parame-
Button
ter reset
pressed for
proce-
1 second –
dure.
resetting the
current EZY
(easy con-
figuration)
setting.
19

Publicidad

Tabla de contenido
loading

Tabla de contenido