Starting/Stopping Instructions; Operating Instructions; Maintenance And Repair Instructions - Troy-Bilt TBE515 Manual Del Operador

STARTING/STOPPING INSTRUCTIONS

WARNING:
Operate this unit only in a well- ventilated outdoor area. Carbon monoxide
exhaust fumes can be lethal in a confined area.
WARNING:
Avoid accidental starting. Make sure you are in the starting position when
pulling the starter rope (Fig. 14). To avoid serious injury, the operator and unit must be
in a stable position while starting.
STARTING INSTRUCTIONS
1. Check the oil level in the crankcase. Refer to
Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline.
Refer to Fueling the Unit.
NOTE: There is no need to turn the unit on. The On/Off
Stop Control is in the ON ( I ) position at all times
(Fig. 11).
3. Fully press and release the primer bulb 10 times,
slowly. Some amount of fuel should be visible in the
primer bulb and fuel lines (Fig. 12). If you can't see
fuel in the bulb, press and release the bulb as many
times as it takes before you can see fuel in it.
IF UNIT IS BELOW 40°F... move the Cold Weather Start
Lever to the closed position (Fig. 13) and continue to
step 4. DO NOT move this lever to the closed position
if the unit's temperature is above 40°F.
4. Stand in the starting position (Fig. 14) and make sure
the throttle control (Fig. 15) is in the SLOW (
position.
5. Pull the starter rope out a short distance until you feel
some resistance (this is usually around 2-4 inches).
Then pull the starter rope smoothly and briskly 5
times. The engine should start.
NOTE: Do not engage the bail while pulling the starter
rope (Fig. 14) or the unit will not start.
6. If the engine starts, move the throttle control to the
FAST ( ) position and allow the engine to warm up
for 15 to 30 seconds.
IF ENGINE STARTS AND WEATHER IS COLD... (below
40°F), move the Cold Weather Start Lever to the open
position (Fig. 13) and let the engine warm up for 30 to
60 seconds.
IF... the engine does NOT start, go back to step 3.
IF... the engine stops while the throttle control is in the
FAST ( ) position, go back to step 4.
WARM UNIT RESTART... Once the engine is warm,
move throttle control lever to the SLOW (
position and pull the starter rope to restart. Do not
squeeze the bail while pulling the starter rope.
NOTE: The unit uses the Incredi-Pull™ starting system
with MAX FIRE IGNITION™ , which significantly
reduces the effort required to start the engine.
You must pull the starter rope out far enough to
hear the engine attempt to start. There is no need
to pull the rope briskly-- there is no harsh
resistance when pulling. Be aware that this
starting method is vastly different from (and much
easier than) what you may be used to.
STOPPING INSTRUCTIONS
1. Release your hand from the bail and move throttle control
lever to the SLOW ( ) position. Allow the engine to cool
down by idling.
WARNING:
Do not force the throttle control
handle back past the Turtle on the throttle label.
This could damage the unit.
2. Press and hold On/Off Stop Control in the OFF (O) position
until engine comes to a complete stop (Fig. 11).
On/Off
Switch
Fig. 11
Primer Bulb
)
Fig. 12
Cold Weather Start Lever
Open Closed
)
Fig. 13
Bail
Starter
Rope
Fig. 14
Fast
Throttle
Control
Slow
Throttle Label
Fig. 15

OPERATING INSTRUCTIONS

HOLDING THE UNIT
WARNING:
Always wear eye, hearing, foot and body protection to reduce the risk of
injury when operating this unit.
Before operating the unit, stand in the operating position (Fig. 16).
Check for the following:
• The operator is wearing eye protection and proper clothing.
• Both hands are holding the handle bar firmly.
• The edger wheel adjusted for proper cut depth as shown in
Figure 17 and edger positioned as shown in Figure 16.
ADJUSTING EDGER CUTTING DEPTH
1. Grasp the depth adjustment lever located beside the front
wheel (Fig. 17).
2. To raise the cutting blade, move the lever toward the front of
the wheel bracket (Fig. 17).
3. To lower the cutting blade, move the lever toward the rear of
the wheel bracket.
OPERATING THE UNIT
Once the unit has started:
1. Tilt the unit back until the blade is not in contact with the
ground.
2. Lift the bail (Fig. 16) and hold it against the unit's handle to
engage the blade and keep it rotating.
3. Slowly lower the unit until the front wheel is in contact with the
ground.
NOTE: Make sure you have a firm grip on the unit. The spinning
blade will contact the ground before the wheel does and
will create continuous forward thrust.
4. Walk slowly behind the unit while maintaining a firm grip on
the unit.
TIPS FOR BEST EDGING RESULTS
• Do not force the edger. Edge the first time at a lesser
depth,(No more than 1/2" depth cut per pass), then do the area
again with a deeper setting.
• Walk the edger at a slow, even pace.
• Check the blade condition. As it wears it becomes smaller,
thus reducing the cutting depth performance. Replace with a
new blade when the blade has worn to the blade's wear limit
holes (Fig. 18).
ADJUST BELT TENSION
If blade fails to turn when the bail is pulled, then:
1. Locate small thumb wheel on top of the belt housing (Fig. 17).
2. Turn the wheel clockwise 1 revolution to increase the tension
on the belt.
3. Try pulling the bail and see if the blade turns. If not, repeat
step 2 until the blade turns.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING:
To prevent serious injury, never perform maintenance or repairs with unit
running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure
that the unit cannot start.
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the frequency stated in the table. These procedures
should also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these
procedures take your unit to a Troy-Bilt or other qualified service dealer.
NOTE: Maintenance, replacement, or repair of the emission control devices and system may be
performed by a Troy-Bilt or other qualified service dealer.
In order to assure peak performance of your engine, inspection of the engine exhaust port may be
necessary after 50 hours of operation. If you notice lost RPM, poor performance or general lack of
acceleration, this service may be required. If you feel your engine is in need of this inspection, refer
service to a Troy-Bilt or other qualified service dealer for repair. DO NOT attempt to perform this process
yourself as engine damage may result from contaminants involved in the cleaning process for the port.
FREQUENCY
Fill fuel tank with fresh fuel
Before using
Check Oil
Every 10 hrs Clean and re-oil air filter
After 1st 10 hrs Change Oil
Every 25 hrs Change Oil
Every 25 hrs Clean Spark Arrestor
Every 10 hrs Check rocker arm to valve clearance and adjust
Verey 25 hrs Check rocker arm to valve clearance and adjust
Every 25 hrs Check spark plug condition and gap
Fig. 16
Wheel Bracket
Fig. 17
Blade Edges
Fig. 18
MAINTENANCE REQUIRED
Lift Bail
Thumb
Wheel
Depth
Adjustment
Lever
Wear Limit
Holes
SEE
p. 4
p .6
p. 6
p. 6
p. 6
p. 7
p. 6
p. 6
p. 7
5