Additional Safety Instructions For Plunge Saws - stayer CPT3000E Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates
of our machines on the website: www.grupostayer.com
The plunge saw is intended to cut wood and similar
materials, gypsum and cement-bonded fiber materials
and plastic. With compatible special saw blades the
plunge saw can also be used to cut aluminum.
The plunge saw is only to be used with a
specifically designed guide rail. Installation in a
differenct or homemade guide rail or workbench
can cause serious accidents.
WARNING! Read this manual and general
safety instructions carefully before using the
appliance, for your own safety. Your power
tool should only be passed on together with
these instructions.
1. INDEX
2. ADDITIONAL SAFETY INSTRUCTIONS FOR
PLUNGE SAWS ................................................... 20
3. Instructions for use
3.1 Placement tool..................................................... 21
3.2 Assembly............................................................. 21
3.3 Description .......................................................... 22
4. Operating instructions.................................... 22
4.1 Switching ON/OFF......................................... ..... 22
4.2.Setting the cutting depth ..................................... 22
5. Maintenance and service instructions.......... 24
5.1 Cleaning And Maintenance ................................. 24
5.2 Repair service...................................................... 24
5.3 Warranty ............................................................. 24
5.4 Disposal and recycling......................................... 24
6. Regulations ..................................................... 24
6.1 Technical Data..................................................... 24
6.2 EU declaration of conformity................................ 25
2. ADDITIONAL SAFETY INSTRUCTIONS
FOR PLUNGE SAWS
- Make sure that the mains voltage matches the
specifications on the type plate.
- Persons with restricted physical, sensory or mental
capabilities are not allowed to use the plunge saw
unless they are supervised and instructed by a
guardian.
- Never leave the powered-on saw unattended and keep
them out of reach of children and persons in need of
supervision.
- Do not bring your hands in the cutting area and the saw
blade.
- Keep in mind that even a worn saw blade is still very
......................................... ...
ENGLISH
20
sharp. Always grasp the saw blade on the sides. Do not
fling the saw blade and do not drop it.
- Never use the plunge saw with grinding wheels.
- Do not grip underneath the workpiece. The protective
cover cannot protect you from the saw blade under the
workpiece.
- Adjust the cutting depth to the thickness of the
workpiece. It should be visible less than a full tooth
height under the workpiece.
- Do not cut very small workpieces. When cutting round
wood, use a device which secures the workpiece from
twisting. Never hold the workpiece to be cut in your
hand or across your leg. It is important to secure the
workpiece properly to minimise the risk of physical
contact, jamming of the saw blade or loss of control.
- Hold the saw only by the insulated gripping surfaces
when performing an operation
where the cutting tool may come into contact with
hidden power lines or its own device cable. Contact
with a live wire also exposes the metal parts to tension
and leads to an electric shock.
- Use always saw blades in the correct size and with
suitable locating bore. Saw blades that do not match
the mounting parts of the saw will run unevenly and
page lead to loss of control.
- Never use a damaged or incorrect outer flange or a
damaged clamping screw. The outer flange and the
clamping screw have been specially designed for your
saw for optimum performance and reliability.
21
- Start the plunge saw and begin cutting when it reaches
the full idling speed.
- Never brake the saw blade using lateral pressure after
switching it off.
- Set the saw aside only when the saw blade comes to a
standstill.
- Do not expose the saw to high temperatures, humidity
and strong shocks. The saw can be damaged as a
result.
- Hold the saw firmly with both hands and bring your
arms into a position in which you can resist the kickback
forces
CAUSES AND PREVENTION OF KICKBACK
- A kickback is the sudden reaction as a result of a
stuck, jammed or misaligned saw blade which leads
to an uncontrolled saw to be lifted and moved from the
workpiece out in the direction of the operator.
- A kickback can occur when the saw blade gets stuck or
jammed in the saw gap. The saw blade is blocked and
the motor force repels the circular saw in the direction
of the operator.
- A kickback can occur when the saw blade becomes
twisted or misaligned in the saw groove. As a result,
the teeth of the back edge of the saw blade can get
stuck in the surface of the workpiece, whereby the saw
blade is moved out of the saw gap and the saw jumps
back in the direction of the operator.
- A kickback is the result of incorrect or faulty use of the
saw. It can be prevented by appropriate precautions as
described below.
- Hold the saw firmly with both hands and bring your
arms into a position in which you can resist the kickback
forces. Always hold the saw baldes on the sides, never
20