Bosch GOP Professional 30-28 Manual Original página 21

OBJ_BUCH-2566-002.book Page 21 Friday, June 17, 2016 1:16 PM
Accessory
HM-Riff sanding
finger
HM-Riff plunge cut
saw blade
HCS universal joint
cutter
BIM plunge cut saw
blade, wood and
metal
TC plunge cut saw
blade, metal
BIM plunge cut saw
blade, wood and
metal
HCS plunge cut saw
blade, wood
Mounting/Replacing the Application Tool/Accessory
(GOP 30-28)
If required, remove an already mounted application tool/
accessory.
For removing the application tool/accessory, loosen the
screw 6 with the hex key 7 and remove the application
tool/accessory.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 5) in such a manner on the tool holder 4 that the
offset faces downward (see illustration on the graphics page;
marking on the application tool/accessory is readable from
above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 4. 12 different positions are possible, each
offset by 30°.
Bosch Power Tools
Material Application
Wood, Sanding wood or paint in hard to reach areas without
Paint sanding paper;
example: sanding off paint between shutter louvres,
sanding wooden floors in corners
Fibreglass, Plunge cuts in severely abrasive materials;
Mortar, example: routing thin mosaic tiles
Wood
Expansion joints, Cutting and separating soft materials;
Putty, example: cutting silicone expansion joints or putty
Insulation materials (rock
wool)
Softwood, Fast, deep plunge cuts in wood and metal;
Hardwood, example: quick cutting of wood containing nails, deep
Veneered panels, plunge cuts in laminated panels and precise shortening of
Plastic-laminated panels, door frames
Non-hardened nails and
screws
Stainless steel (Inox), Fast, deep plunge cuts in severely abrasive materials or
Screws and nails, metal;
Epoxy resin, example: fast cutting of kitchen front covers, easy cutting
Glass fibre reinforced through hardened screws, nails and stainless steel
plastics,
Fibreglass,
Plasterboard,
Porous concrete
Wood, Fast, deep plunge cuts in wood, abrasive wooden materials
Abrasive wooden and plastics;
materials, example: fast cutting of non-ferrous metal pipes and pro-
Plastics, files with smaller dimensions, easy cutting of non-hardened
Hardened nails and nails, screws and steel profiles with smaller dimensions
screws,
Non-ferrous metal pipes
Softwood, Fast, deep separating and plunge cuts; also for sawing
Dowels, close to edges in corners and hard to reach areas;
Tenons, example: deep plunge cut in softwood for installing a
Furniture components ventilation grid
Fasten the application tool/accessory with bolt 6. Tighten the
bolt with hex key 7 until the spring washer of the bolt faces
flush against the application tool/accessory.
 Check the tight seating of the application tool/accessory.
Incorrect or not securely fastened application tools/accesso-
ries can come loose during operation and pose a hazard.
Mounting/Replacing the Application Tool/Accessory
(GOP 40-30/GOP 55-36)
If required, remove an already mounted application tool/ac-
cessory.
To do so, open the SDS lever 12 all the way. The application
tool/accessory will be ejected.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 5) in such a manner on the tool holder 4 that the
offset faces downward (see illustration on the graphics page;
marking on the application tool/accessory is readable from
above).
English | 21
1 609 92A 33B | (17.6.16)