FLAEM RF7 Plus Manual De Instrucciones página 9

CLEANING, SANITISATION, DISINFECTION, STERILISATION
Switch off the device before any cleaning procedure and unplug the power cable from the socket.
DEVICE AND TUBING EXTERIOR
Use only a damp cloth with antibacterial soap (non-abrasive and with no solvents of any sort).
ACCESSORIES
Open the nebuliser by turning the upper part (11.3) anticlockwise, remove the nozzle (11.2)
from the upper part (11.3) by pressing as shown by the 2 arrows in the "Connection diagram"
in point 11.
Then proceed according to the following instructions.
CLEANING AT HOME - SANITISATION AND DISINFECTION
SANITISATION
Before and after each use, sanitise the nebuliser cup and the accessories, choosing one of the
methods described below.
method A: Sanitise accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 under potable hot
water (approximately 40°C) with a gentle, non abrasive dish detergent.
method B: Sanitise accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 in the dishwasher with
a hot cycle.
method C: Sanitise accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 by immersing them in
a solution of 50% water and 50% white vinegar, then rinse thoroughly under potable hot
water (approximately 40°C).
If you want to also perform the cleaning for DISINFECTION, jump to the DISINFECTION
paragraph.
After having sanitised the accessories, shake them vigorously and place them on a paper
towel. Alternatively, dry them with a jet of hot air (for example, a hair dryer).
DISINFECTION
After sanitising the nebuliser cup and the accessories, disinfect them choosing one of the
methods described below.
method A: Accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 can be disinfected.
The disinfectant must be an electrolytic chloroxidizer (active principle: sodium hypochlorite)
specific for disinfecting, which is available in any pharmacy.
Implementation:
- Fill a container big enough to hold all of the parts to disinfect with a solution of potable
water and disinfectant, according to the proportions indicated on the packaging of the
disinfectant.
- Completely immerse each part in the solution, taking care to avoid the formation of air
bubbles on the parts. Leave the parts immersed for the amount of time indicated on the
packaging of the disinfectant associated with the concentration chosen for the solution.
- Remove the disinfected parts and rinse abundantly with warm potable water.
- Dispose of the solution following the instructions provided by the disinfectant
manufacturer.
method B: Sanitise the accessories 1-2-5-6-8-9-11.1-11.2-11.3-11.4 by boiling them in
water for 20 minutes; use demineralised or distilled water to prevent calcium deposits.
method C: Sanitise the accessories 1-2-5-6-8-9-11.1-11.2-11.3-11.4 with a hot steam
steriliser for baby-bottle (not the microwave type). Perform the process faithfully following
the instructions of the steriliser. To ensure that the disinfection is effective, choose a steriliser
with an operating cycle of at least 6 minutes.
After having disinfected the accessories, shake them vigorously and place them on a paper
towel. Alternatively, dry them with a jet of hot air (for example, from a hair dryer).
CLEANING IN A CLINICAL OR HOSPITAL SETTING - DISINFECTION AND STERILISATION
Before disinfection or sterilisation, sanitise the nebuliser cup and the accessories, choosing
one of the methods described below.
method A: Sanitise accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 under potable hot
water (approximately 40°C) with a gentle, non abrasive dish detergent.
method B: Sanitise accessories 1-2-3-4-5-6-8-9-11.1-11.2-11.3-11.4 in the dishwasher with
9