Remote Control Programming - Comunello CU 24V 1M ONE Instrucciones De Uso

learning procedure, the control unit screens the system for any accessories
installed on the digital BUS line. This operation can introduce delays before
the operators actually move.
NOTE: To check the correct programming of the stroke, you can also use
the STEP BY STEP button as AUTO-PP command (open-close).
NOTE: During the maximum stroke self-learning process, make sure that
the operating leaf is free.

REMOTE CONTROL PROGRAMMING

Remote controls with different codes of either the fixed or rolling code type
can be saved on the control unit.
Programming
Programming (and storage) of the transmission code is done by pressing
the TX CODE button and checking the status of the corresponding LED
(above the TX CODE button) as follows:
1. Press the TX CODE button once: the corresponding led lights up and
flashes once (1010). By sending the code of a transmitter button, if the
code is valid, it will be saved with AUTO-PP function (open-close).
2. Press the TX CODE button twice: the corresponding led lights up and
flashes twice (110110). By sending the code of a transmitter button, if the
code is valid, it will be saved with PED function (pedestrian).
3. Press the TX CODE button three times: the corresponding led lights up
and flashes three times (11101110). By sending the code of a transmitter
button, if the code is valid, it will be saved with AUX function (2nd auxiliary
channel).
Deletion:
Deletion of all the radio codes is done by pressing the TX CODE button and
checking the status of the corresponding LED (above the TX CODE button)
with the following association:
1. Press the TX CODE button four times: the corresponding led lights up
permanently (steady). To confirm the deletion, press the TX CODE button
again (the corresponding led starts to flash) and keep it pressed until the led
stops flashing, which confirms the successful deletion of all codes saved
in the system.
1 2 3 4 5 6 7 8 9 10
Programming buttons
CODE TX Remote control programming
ACCESSORIES DETECTION (BUS LINE)
The control unit automatically detects all the ONE accessories wired on the
BUS line, checking the type of accessory, its numeric identifier ID and the
type of operation set (MODE). Always make sure to use accessories with
different ID for each type of accessory (par: ACCESSORY ADDRESS
ASSIGNMENT). The system also detects the accessories installed on
the BUS line:
1 Before the maximum stroke self-learning process (AUTOSET). At this
stage, the system detects the accessories installed and saves the
system configuration (e.g.: new installation).
2 Each time you press the RESET button. At this stage, the system re-
reads the accessories installed, but does not change the initial system's
configuration (accessories saved).
NOTE: The detection of the accessories is an automatic operation that may
cause a delay in the system configuration proportionate to the number of
accessories installed.
NOTE: Make sure you have set the ID and MODE (operating mode) on all
accessories installed, before connecting them to the digital BUS line.
IMPORTANT! If you want to configure the system with COMUNELLO
ONE app access (requires the use of tablet with wireless connection
26
COMUNELLO ®Copyright 2017 - All rights reserved
and a K-ONE access key - code ONE KEY), keep the MODE dip-
switches set to OFF (TYPE 1 operating mode) for all accessories
connected to the BUS line.
ADJUSTMENTS FROM COMUNELLO ONE APP
The control unit features an additional advanced access for system
configuration. Using the (optional) accessory K-ONE (code ONE KEY),
you can connect to the control unit via Wi-Fi radio and proceed to its full
configuration following a simple and guided procedure, with the aid of the
COMUNELLO ONE app that you can download from our online store.
To use the app COMUNELLO ONE, you will need a wifi device (tablet or
smartphone) with Android or iOS operating system.
Connector for K-ONE module
Configuration via the COMUNELLO ONE app allows you to configure and
adjust all the parameters of the system in a fast and easy way, monitor its
operation, manage the list of saved remote controls, copy the configuration
to another equivalent system and plan maintenance.
ADDITIONAL ADJUSTMENTS FROM THE APP:
Guided procedure to check direction of rotation of the operators and
change their settings.
1 2 3 4 5 6 7 8 9 10
Commands
Set the pause time (automatic closing)
Enable Permanent Close.
Force/Speed
Adjust maximum operator speed during opening cycle
Adjust maximum operator speed during closing cycle
Adjust deceleration speed during opening cycle
Adjust deceleration speed during closing cycle
Start Operator 1 deceleration during opening cycle
Start Operator 1 deceleration during closing cycle
Adjust pedestrian opening
Enable/Disable Operator Brake
Enable/Disable Soft Stop
Enable/Disable Soft Start
Enable/Disable Release Stroke
Enable/Disable Slam Lock
Remote controls
Read saved codes and set function
Assign a text string for each code
Delete single code
Add a new code
Check the presence of a code
Photocells
Enable/Disable Partial Inversion during Closing cycle
Enable/Disable Partial Inversion during Opening cycle
Enable/Disable Follow-Me
Operation test
Assign a text string for each photocell
Set the MODE (operation) of each photocell
Key switches
Operation test
Assign a text string for each key switch
Set the MODE (operation) of each key switch
Flashing lights
Enable/Disable Closing Pre-Flash
(0"..40 min)
(10%..100%)
(10%..100%)
(10%..100%)
(10%..100%)
( 0%..100%)
( 0%..100%)
(10%..100%)