DeWalt DCV581H Manual De Instrucciones página 11

2. Unlatch the tank latches
from the tank. Twist the filter
from the power head.
Fig. F
3. Clean the filter by shaking off excess dust, tapping into
a waste receptacle, then rinsing under running water.
Depending on the condition of the filter, a water wash is
not always required. Do not use a brush to clean filter.
4. Reinstall and secure the filter onto power head by
twisting the filter to the left.
5. Replace power head onto the tank and secure latches.
Blower (Fig. A)
The blower function can be used to remove debris from
behind small spaces, to dry a damp floor, to blow grass
clippings or leaves from an outside walk, patio, etc.
To Use as a Blower
1. Empty the tank following the instructions under the
Vacuum Cleaning section of this manual.
2. Twist the vacuum hose 2
3. Insert the hose into the side exhaust port
to secure.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
• Empty the vacuum often, especially when wet debris is
in the canister.
• MAINTAIN TOOL WITH CARE. Keep the side exhaust port
clean and unblocked for best and safest performance.
• Do not attempt to repair the vacuum. To assure
product safety and reliability, repairs, maintenance,
and adjustments should be performed by authorized
D WALT service centers.
e
Cord, Hose and Accessory Storage (Fig. A)
When the vacuum is not in use, the power cord should
be secured around the vacuum handle underneath the
cord wrap 10 . The vacuum hose can be wrapped around
appliance, underneath the battery interface, and secured
with the hose clip also located at the back of the vacuum.
7
The two accessories (crevice tool and wide nozzle) can be
stored on board the vacuum as well.
4 and remove the power head
5 to the right to remove it
5
to remove.
6 and twist
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
The DCV581h includes a 1-1/4" hose, crevice tool (stored in
the handle) and wide nozzle.
A replacement filter is available at extra cost at your local
D WALT service center.
e
Dust Collector (Fig. G)
In the vacuum mode, the appliance can also function as a
dust collector for power tool applications producing dust
or debris.
Install the DWV9000 dust extraction adaptor, availiable at
additional cost, to facilitate connection of a power tool to
the vacuum hose 2 .
Fig. G
2
1. Unscrew and remove the standard hose nozzle.
English
WALT
e
WALT Industrial
e
9