Assembly - Powerfix Profi Z15003 Instrucciones De Montaje

Assembly

©
Assembly
CAUTION! DANGER OF FIRE! Assemble
and use the product on a fire-resistant surface only.
The following tools are required for
assembly:
7 x Open spanners (1 x 8 mm, 2 x 10 mm,
2 x 14 mm, and possibly 2 x 17 mm)
2 x Allen key
1 x Slotted head screwdriver (approx. 5 mm)
Follow these steps:
Fasten the saddle on to the base plate
33
with the hexagonal socket head screws
and washers (see Fig. A).
34
Fasten the handle on to the mount
3
the projecting screw thread and the corresponding
nut (see Fig. A).
Note: Please bear in mind that the angle
grinder must be fitted with a suitable cutting
disc before assembly. It is not possible to
change the disc with the angle grinder installed
in the stand.
Now mount the angle grinder in the mount
Note: At this point, first check the size of the
handle thread of your angle grinder. It may be
M6, M8 or M10.
Then place the corresponding mounting bolts
, , washers and matching nuts
10 11 8
, distance pieces
14 15
bushings , to one side, ready for use.
6 7
Insert the necessary plastic bushings
into the mounting pieces
Note: Ensure that the size of the plastic bush-
ings , matches the required mounting
6 7
bolts , . Plastic bushings are not required
9 10
for mounting bolts M10
Screw the matching mounting bolt
through the rear mounting piece
Fasten the rear mounting piece
tightening the corresponding size of nut
on the mounting bolt
14
turning it in the direction of the mounting piece
(see Fig. B).
Insert the adjustment screw
tom hole and the adjustment screw
26 GB/MT
32
35
with
36
.
36
,
9
, ,
12 13
, , and plastic
16 17
,
6 7
, (see Fig. B).
18 38
.
11
, ,
9 10 11
(see Fig. B).
38
in place by
38
, ,
12 13
, , (i.e. by
9 10 11
)
38
through the bot-
20
through
1
the top hole of the mount
36
the rubber buffers of these screws must lie
against the angle grinder housing.
Note: First insert these screws so that the rubber
buffers lie directly against the mount
Now push the plastic locating pieces
mounting pieces , on to the guide of the
18 38
mount (Figure B).
36
Then attach the mounting pieces
through the plastic locating pieces
hexagonal socket head screws
gated holes in the mount
36
Place the desired distance piece
the mounting bolt , ,
9 10 11
on to the front mounting piece
Note: The three distance pieces
are of different lengths. Choose the distance
piece , , of the most appropriate length.
15 16 17
Note: Set the distance piece
that the cutting disc cannot come into contact
with the workbench / table below the base
plate (see Figure E).
32
Screw the matching mounting bolt
through the front mounting piece
Fasten the front mounting piece
tightening the corresponding size of nut
on the mounting bolt
14 9
turning it in the direction of the mounting piece
Now set the adjustment screws
the angle grinder is aligned at right angles to
the base plate and firmly attached to the
32
mount .
36
After slightly loosening the hexagonal socket
head screws , adjust the saddle
35
the cutting disc of the angle grinder lowers into
centre of the slot provided in the base plate
Now attach the safety guard
push the safety guard on to the metal rod
5
and fasten it in place with the nut
Now insert the metal rod
2
sponding opening in the mount
it in place with the nut and the mounting
39
(see Fig. ).
bolt
40
Always keep the angle grinder's mains lead in
place using the clip .
37
After assembly is complete, switch the angle
grinder on for a few seconds and then switch it
. Note that later
.
36
of the
19
,
18 38
with the
19
in the elon-
31
(see Fig. A).
, , on
15 16 17
and washer
8
(see Fig. D).
18
, ,
15 16 17
, , so
15 16 17
, ,
9 10 11
.
18
in place by
18
, ,
12 13
, , (i.e. by
10 11
).
18
, so that
1 20
so that
33
.
32
. To do this
5
2
(see Fig. C).
4
into the corre-
and fasten
36