Hudora 74501 Instrucciones De Montaje página 4

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component of
the product. Therefore, please store them and the packaging carefully in case questions
arise in the future. Please always include these instructions when handing on the product
to a third party. This product must be assembled by an adult. This product is designed
for private/domestic use only. This product is not designed for commercial/industrial use.
The use of the product requires certain capabilities and skills. Always adjust according to
the age of the user and use for the purpose it has been designed for.
TECHNICAL SPECIFICATIONS
Item: Punchingball with boxing gloves and pump
Item number: 74501, 74506
Adjustable height: 100 to 130 cm
Item weight: approx. 2.7 kg
Purpose: Device to train speed, accuracy and coordination.
If you have assembly problems or would like further information on the product, we have
all you need and more at http://www.hudora.de/.
CONTENTS
1 x Box set (see parts list on page 2) | 1 x These instructions
Other items are meant to facilitate safe transportation and are not required for the instal-
lation and use of the product.
SAFETY INSTRUCTIONS
• Although the box set is designed for children and adolescents, it is not a toy. Please
ensure the perfect technical condition of the boxing equipment! In the case of damage
or lose connecting elements don't use the product anymore.
• Adjustments to the product or use of non-original parts can lead to accidents.
• Without or with too little ballast, the punching ball is not sufficiently stable. Fill it suf-
ficiently with water or sand before use and check that it is stable before training. We
recommend filling the base with sand instead of water, as water can leak if there is a
defect, causing the product to fall over and resulting in property damage or personal
injury.
• Before use chose a location for training with sufficient space, so that no damage can
be caused to persons or other objects.
• During training boxing gloves of a suitable size should always be worn.
• Please use the enclosed gloves only in combination with this punching ball. The gloves
are not designed for real boxing matches.
INSTRUCTIONS ON ASSEMBLY
Step 1
Remove all parts from the packaging. Next pump up the ball (10). To do this, screw the
valve adapter (11) onto the pump, moisten it and insert it into the valve of the ball. Pump
until the ball is hard (not too hard otherwise it could burst. If the ball is too hard boxing
can become painful!) Remove the pump and keep it safe, as the ball could lose pressure
over time. If you wish to deflate the ball, simply pierce the valve using the valve adapter.
Step 2
Next, screw the ball onto the telescopic tube (9). For best mounting, two different screws
should be used to fix the ball in place. For the lower cross screw, make sure the inner
tube is screwed in in such a way that the borehole is completely open and the screw can
penetrate easily. Following this, bolt the cross screw together with a cap nut and two lock
washers. Another smaller screw must then be screwed into the upper hole.
Step 3
Now it is time for the base: Is the plastic sleeve already on the spring (7)? If not, first
place it over the spring so that no hair or fingers can get caught in the spring thread. Then
place the metal plate with the hole (5) in it over the pipe with the spring (7) as shown in
the picture. Now insert the guide sleeve (2) into the base (1) from above and push the
tube with the spring (7) through along with the metal disc (5). Mount another guide sleeve
(2) and a centering plate (4) before fixing the entire construction with the Allen key (6).
Step 4
A suitable key is provided to tighten the Allen screw. The screw has a type of glue on the
thread and is therefore more difficult to tighten. This is to prevent it from becoming lose.
If the screw is tightened often it can cause wear and become unsafe, which would require
the screw to be replaced. Now place the standpipe (8) on top; it fits into the spring knob on
the spring pipe. Finally tighten the telescopic pipe (9). To do this loosen the screw on the
standpipe and slide the pipes into each other. There are markings 50mm from the bottom
end of the telescope pipe. The pipe must not be lifted further than these markings, as
the clamp would then no longer be safe. Make sure that clamping screw is screwed tight
during use so that the ball cannot move on its own.
Step 5
Now fill the base with sand, gravel or water and place the cap (3) on the opening. If you
decide to fill the punch ball with water, make sure that you only use it on surfaces which
are not water-sensitive!
All images are examples of the design.
MAINTENANCE AND STORAGE
Use only a dry or damp cloth to clean the product; do not use special cleaning agents!
Check the product for damage or traces of wear and tear before and after each use. Do
not make any structural changes. For your own safety, please use original spare parts
only. These can be sourced from HUDORA. If parts become damaged or if sharp edges
or corners should develop, the product may not be used any more. If in any doubt, please
contact our service team (http://www.hudora.de/service/). Store the product in a safe
place where it is protected from the elements, cannot be damaged, and cannot injure
anyone.
• We advise that the set is stored in a dry and dark place. When necessary clean your
set using a slightly damp cloth. Moisture on the metal parts of the equipment can lead
to rust and should therefore be avoided.
• Please protect the enclosed gloves from moisture. After use we advise that the gloves
are kept in a dry and well ventilated place.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection point
provided in your area. Local waste management companies will be able to answer your
questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we put just
as much effort into rectifying them. You can find numerous information on the product, re-
placement parts, solutions to problems and lost assembly manuals at http://www.hudora.
de/service/.
4/8